Zhangxueyou gave a wrong item, Sanguinololu cannot support a dual extruder.Aloneguy wrote:Now I have Prusa Pro B Kit with control board is Sanguinololu , What product I need for upgrade to Dual Extruder? Thank you
Search found 104 matches
- Mon Jun 22, 2015 2:44 pm
- Forum: Products FAQ
- Topic: Can Geeetech i3 Prusa Pro B upgrade to Dual Extruder
- Replies: 7
- Views: 14500
Re: Can Geeetech i3 Prusa Pro B upgrade to Dual Extruder
- Fri Apr 10, 2015 5:04 pm
- Forum: Extruder
- Topic: Prusa I3 Pro B Black Acrylic Heating/extruder issues
- Replies: 21
- Views: 32640
Re: Prusa I3 Pro B Black Acrylic Heating/extruder issues
I saw your pictures and now I have a question, do you mean you pluged a same thermistor into the bed thermistor slot and hotend thermistor to measure the temperature, but you got 2 different values, one is 18 degree and the other is 140 degree? I only want to know that can you get right value from ...
- Thu Apr 09, 2015 2:21 pm
- Forum: Stepper Motor
- Topic: All axis only move in positive direction
- Replies: 25
- Views: 36240
Re: All axis only move in positive direction
I sent a m119 through repetier host for each endstop. They all showed open. Then i would hold each endstop down and sent another m119 each time and they would show triggered for the one i pressed. That rules out the end stops. I have updated the firmware, no luck. I have swapped around the steppers ...
- Wed Apr 01, 2015 9:45 am
- Forum: Extruder
- Topic: Extruder problems
- Replies: 15
- Views: 29710
Re: Extruder problems
Please adjust the screw next to the filament hole, it makes the pressure between wheel and filament to be tight or loose.
Sometimes a high temperature is useful.
Sometimes a high temperature is useful.
- Wed Apr 01, 2015 9:36 am
- Forum: LCD Panel
- Topic: LCD showing blocks after RAMPS flash. Nothing works anymore
- Replies: 4
- Views: 9736
Re: LCD showing blocks after RAMPS flash. Nothing works any
Did your LCD display right before, even once? How about it when you first used it? We need to confirm it's a software or a hardware issue.
- Wed Apr 01, 2015 9:29 am
- Forum: Stepper Motor
- Topic: Acrylic prusa i3 ramps 1.4 mega 2560 motor problems
- Replies: 6
- Views: 12460
Re: Acrylic prusa i3 ramps 1.4 mega 2560 motor problems
The logic level in endstop is inverse, so it always get a inverse signal which is not expected. There is a simple way to know it's right or wrong. Press the endstop and then home axis, if the axis move in right direction, it means the endstop's logic level is wrong. You had better check X axis ...
- Tue Mar 31, 2015 11:28 am
- Forum: Stepper Motor
- Topic: All axis only move in positive direction
- Replies: 25
- Views: 36240
Re: All axis only move in positive direction
dose it move only a little bit? If it's, pls press the endstop and move it again, i guess the endstop signal is missing or get a inverse level.
- Tue Mar 31, 2015 10:37 am
- Forum: Others
- Topic: Prusa i3 Pro Y-axis Layer shift problem
- Replies: 3
- Views: 8173
Re: Prusa i3 Pro Y-axis Layer shift problem
Could you take a photo for the part you printed and paste it here? It will be helpful.
- Tue Mar 31, 2015 10:21 am
- Forum: Software
- Topic: Problem to connect to Repetier
- Replies: 11
- Views: 19074
Re: Problem to connect to Repetier
You don't need to re-upload a firmware, we had uploaded a Marlin firmware for your machine.
Can you home all axis when clicking on HOME button?
Visit the wiki page for your motherboard and it will show you how to connect a LCD screen.
Can you home all axis when clicking on HOME button?
Visit the wiki page for your motherboard and it will show you how to connect a LCD screen.
- Tue Mar 03, 2015 10:15 am
- Forum: Others
- Topic: Printer dead? (Acrylic Geeetech I3 pro B)
- Replies: 35
- Views: 47590
Re: Printer dead? (Acrylic Geeetech I3 pro B)
Yes, you are right.