Printer would not connect after updating to 1.0.5 firmware
the firmware was successfully updated, it works as a standalone, however , i can't connect it to the PC anymore
any suggestions?
Edan
Search found 8 matches
- Tue Jun 14, 2016 9:31 pm
- Forum: Firmware
- Topic: Printer would not connect after updating to 1.0.5 firmware
- Replies: 1
- Views: 4139
- Tue Jun 14, 2016 8:25 pm
- Forum: Products FAQ
- Topic: Prusa M201 Hot End keeps clogging
- Replies: 1
- Views: 4043
Prusa M201 Hot End keeps clogging
Hello Geeetech.
I am using two Colorfabb PLA filaments on the 2-to-1 extruder, the hotend keeps doing one of the two:
a) Jams completely.
b) jams partially - and then only one color can be extruded.
whenever I raise the temprature try to unclog using this method, I end up melting the PLA inside ...
I am using two Colorfabb PLA filaments on the 2-to-1 extruder, the hotend keeps doing one of the two:
a) Jams completely.
b) jams partially - and then only one color can be extruded.
whenever I raise the temprature try to unclog using this method, I end up melting the PLA inside ...
- Wed May 13, 2015 3:34 am
- Forum: Stepper Motor
- Topic: Z axis motors underpowered?
- Replies: 16
- Views: 20064
Re: Z axis motors underpowered?
Hi, first of all costumer service is sending me a new component - which is a good sign.
the second thing is that the component was already mounted to my board when i got the kit, the only thing i did was placing the heat sink
thanks for your attention
Edan
the second thing is that the component was already mounted to my board when i got the kit, the only thing i did was placing the heat sink
thanks for your attention
Edan
- Mon May 11, 2015 1:42 am
- Forum: Stepper Motor
- Topic: Z axis motors underpowered?
- Replies: 16
- Views: 20064
Re: Z axis motors underpowered?
Hi , Two things
a) i tried to switch places with the A4988 module ,and my z axis works.... - which means the module isn't working properly
b) please read Geeetech datasheet about the maximum voltage for this component : http://www.geeetech.com/Documents/A4988-Datasheet.pdf
c) please send me another ...
a) i tried to switch places with the A4988 module ,and my z axis works.... - which means the module isn't working properly
b) please read Geeetech datasheet about the maximum voltage for this component : http://www.geeetech.com/Documents/A4988-Datasheet.pdf
c) please send me another ...
- Sun May 10, 2015 3:11 pm
- Forum: Stepper Motor
- Topic: Z axis motors underpowered?
- Replies: 16
- Views: 20064
Re: Z axis motors underpowered?
obviously, this is where i measure....
- Fri May 08, 2015 11:09 pm
- Forum: Stepper Motor
- Topic: Z axis motors underpowered?
- Replies: 16
- Views: 20064
Re: Z axis motors underpowered?
please - see for yourself...
https://www.youtube.com/watch?v=u9whUsBq578
https://www.youtube.com/watch?v=u9whUsBq578
- Thu May 07, 2015 2:02 pm
- Forum: Stepper Motor
- Topic: Z axis motors underpowered?
- Replies: 16
- Views: 20064
Re: Z axis motors underpowered?
I have tried that, the screw is very jumpy, i can't fix it on 1V
it jumps from 0.3V to around 4.5V in the slightest turn of the screw.
it jumps from 0.3V to around 4.5V in the slightest turn of the screw.
- Thu May 07, 2015 4:00 am
- Forum: Stepper Motor
- Topic: Z axis motors underpowered?
- Replies: 16
- Views: 20064
Re: Z axis motors underpowered?
Hi there, i have the same problem
could you please explain to me what do you mean by that fix?
where do i measure the Voltage?
thanks
could you please explain to me what do you mean by that fix?
where do i measure the Voltage?
thanks