Search found 11 matches
- Sun Aug 23, 2015 9:03 am
- Forum: Others
- Topic: bad prints
- Replies: 1
- Views: 3709
bad prints
after all, i start to print a pyramid test, it starts very well but after the base each line is more at right than the other doing the base at 0 and finishing 3 cm at right what it can be? marlin parametters?wich parametter in that case....
- Wed Aug 19, 2015 8:35 am
- Forum: Others
- Topic: delta g2 printing problem
- Replies: 1
- Views: 3940
delta g2 printing problem
afters a huracan of troubles it start printing, but again a new problem, i take a mini bomb like test because its almost a ball the base is almost perfect but when star going up it begin to put more platic in a side and extend the base( but there is base in this part) and finally i get an amorfical ...
- Mon Aug 17, 2015 8:55 pm
- Forum: Firmware
- Topic: G29 autolevelling destruction G2S
- Replies: 23
- Views: 39351
Re: G29 autolevelling destruction G2S
x y z are good wired cheking manually directions also good
- Sun Aug 16, 2015 4:02 am
- Forum: Firmware
- Topic: G29 autolevelling destruction G2S
- Replies: 23
- Views: 39351
Re: G29 autolevelling destruction G2S
hi guys i have something similar finally g29 succes changing parametters on marlin but when i test a print after g 29 and heating the spider goes dow and touches the bed causing an emergency stop the z eight defined all in the guide defined any idea guys????
- Fri Aug 14, 2015 1:36 am
- Forum: Others
- Topic: Auto leveling on delta G2 :erratic moves
- Replies: 10
- Views: 14233
Re: Auto leveling on delta G2 :erratic moves
i have seent you the reply by messagexd
- Thu Aug 13, 2015 8:36 am
- Forum: Others
- Topic: rocstock g2 print in the air
- Replies: 1
- Views: 4450
rocstock g2 print in the air
hi, i have changed to 196 mm mi axis eight home works g29 works buts onlo do the first hit in the bed after that star climbing and finish between z and x axis i have all modified except the // these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
#define X_PROBE_OFFSET ...
#define X_PROBE_OFFSET ...
- Wed Aug 12, 2015 9:58 pm
- Forum: Others
- Topic: M119 does nothing(mini g2)
- Replies: 3
- Views: 6213
Re: M119 does nothing(mini g2)
ok good idea the log button thanks marc! i have donde the homing fine and the g29 but now im very lost because i dont undertands to much the instructions when i do the probe points the machin begin to go dow until crash with the bed, with auto leveling the machine arrived to the point with ni ...
- Wed Aug 12, 2015 9:33 pm
- Forum: Others
- Topic: Auto leveling on delta G2 :erratic moves
- Replies: 10
- Views: 14233
Re: Auto leveling on delta G2 :erratic moves
okey the big problem was the swicht i have reversed it on the marlin now there is only the thing of the probing points i dont understand it in the guide....
- Tue Aug 11, 2015 8:36 pm
- Forum: Others
- Topic: Auto leveling on delta G2 :erratic moves
- Replies: 10
- Views: 14233
Re: Auto leveling on delta G2 :erratic moves
vedio? the thing is i need to know how to adjust the parameters and the probing points but when i take the spider manually to get the coordinates they dont appear on the ma nual control of repetier
- Tue Aug 11, 2015 8:34 pm
- Forum: Others
- Topic: M119 does nothing(mini g2)
- Replies: 3
- Views: 6213
M119 does nothing(mini g2)
hi guys, the thing is after a lot of problems i arrived to send
G28 i measure the eight oz Z was 193 but when i send M119 notging happens and with G29 it starts to do probe points at the half of the way) of course not touching the bed) hel pleaaase i hsve done the rest of the guide succesfully
G28 i measure the eight oz Z was 193 but when i send M119 notging happens and with G29 it starts to do probe points at the half of the way) of course not touching the bed) hel pleaaase i hsve done the rest of the guide succesfully