Incase anyone wants to know, that was the problem.
Took it right off and started again, needed a small trim and the tensioner on the x and y were set a bit wrong.
Prints are great now.
Thanks for your reply.
Search found 10 matches
- Wed Aug 10, 2016 3:23 pm
- Forum: Print Quality
- Topic: Vibrating Y axis
- Replies: 2
- Views: 6777
- Wed Aug 10, 2016 9:22 am
- Forum: Control Board
- Topic: New endstop sensor
- Replies: 0
- Views: 3540
New endstop sensor
Hi,
I am working on a prusa i3 pro B. Z axis endstop. It has a GT2560 rev A board and I am using marlin pro B with arduino 1.0.1.
I am hoping someone could help me with my sensor. I would like to use a metal detector instead of a mechanical switch. The sensor has an LED that lights up when ...
I am working on a prusa i3 pro B. Z axis endstop. It has a GT2560 rev A board and I am using marlin pro B with arduino 1.0.1.
I am hoping someone could help me with my sensor. I would like to use a metal detector instead of a mechanical switch. The sensor has an LED that lights up when ...
- Wed Aug 10, 2016 8:29 am
- Forum: Firmware
- Topic: Dual extruder steps
- Replies: 1
- Views: 5289
Dual extruder steps
Hi.
I don't understand how to calibrate dual extruders. I would like to print a different support material so the steps on my extruders will be different.
I am using geetech prusa i3 pro B, GT2560, marlin pro B, arduino 1.0.1. slic3r and repetier host
I understand how to do marlin, define ...
I don't understand how to calibrate dual extruders. I would like to print a different support material so the steps on my extruders will be different.
I am using geetech prusa i3 pro B, GT2560, marlin pro B, arduino 1.0.1. slic3r and repetier host
I understand how to do marlin, define ...
- Sat Aug 06, 2016 10:35 am
- Forum: Assembly
- Topic: Endstop wiring
- Replies: 6
- Views: 11862
Re: Endstop wiring
fantastic, thank you.
- Fri Aug 05, 2016 7:57 pm
- Forum: Assembly
- Topic: Endstop wiring
- Replies: 6
- Views: 11862
Re: Endstop wiring
Its just a normal sensor, just the wrong type i guess. Am i able to run it through this board without an external power supply?
- Fri Aug 05, 2016 11:51 am
- Forum: Assembly
- Topic: Endstop wiring
- Replies: 6
- Views: 11862
Re: Endstop wiring
thank you. I now have some more detail. I haven't been happy with the mechanical endstop on my z axis. I have a metal sensor I would like to use. I would like to use the led on the sensor. I don't know much about electronics but researching this I have learnt a little. There are 3 points behind the ...
- Thu Aug 04, 2016 5:20 pm
- Forum: Assembly
- Topic: Endstop wiring
- Replies: 6
- Views: 11862
Endstop wiring
Hi,
Sorry if this is a stupid question, I am hoping to attach a 3 pin and a 4 pin end stop to my prusa i3 PRO B, but the GT2560 only has 2 pins for the end stop connections. Is there an adaption for this?
Sorry if this is a stupid question, I am hoping to attach a 3 pin and a 4 pin end stop to my prusa i3 PRO B, but the GT2560 only has 2 pins for the end stop connections. Is there an adaption for this?
- Sat Jun 25, 2016 10:44 am
- Forum: Firmware
- Topic: Marlin Issue
- Replies: 2
- Views: 5196
Solved
Beautiful, thank you. I hadn't done that previously. Didn't work the first time, but, pressed 'restore', 'load' then 'store' again and its working again now.
your a champion.
your a champion.
- Fri Jun 24, 2016 7:38 pm
- Forum: Print Quality
- Topic: Vibrating Y axis
- Replies: 2
- Views: 6777
Vibrating Y axis
Hi, I am hoping for some help with this issue.
My Y axis seems to have some vibration showing on my prints but only significantly in one direction. I removed the belt and the bed glides smoothly. I tried putting a twist in the belt but that didn't help. there just doesn't seem to be much resistance ...
My Y axis seems to have some vibration showing on my prints but only significantly in one direction. I removed the belt and the bed glides smoothly. I tried putting a twist in the belt but that didn't help. there just doesn't seem to be much resistance ...
- Fri Jun 24, 2016 6:35 pm
- Forum: Firmware
- Topic: Marlin Issue
- Replies: 2
- Views: 5196
Marlin Issue
Hi. I have a Prusa I3 Pro B and am having an annoying issue with marlin I hope someone can help me with.
Everything seems to work through marlin and it seems to be uploading onto the printer, but, I can't change the steps for the extruder, it just doesn't seem to recognise it. Meaning I have to ...
Everything seems to work through marlin and it seems to be uploading onto the printer, but, I can't change the steps for the extruder, it just doesn't seem to recognise it. Meaning I have to ...