Goodmorning
I have instaled correctly the sensor since 1 month,
I have used my print without problem until now but today,
The sensor is blocked but the Led is lighted, when i use the test command, the sensor dont move , after the test command the sensor flash like error response.
Can you help me ...
Search found 9 matches
- Thu Mar 22, 2018 2:05 am
- Forum: Geeetech I3 Pro B
- Topic: 3d touch lvl sensor no move
- Replies: 1
- Views: 3478
- Wed Mar 21, 2018 9:26 pm
- Forum: Geeetech I3 Pro B
- Topic: 3d touch lvl sensor no move
- Replies: 0
- Views: 2917
3d touch lvl sensor no move
Goodmorning
I have instaled correctly the sensor since 1 month,
I have used my print without problem until now but today,
The sensor is blocked but the Led is lighted, when i use the test command, the sensor dont move , after the test command the sensor flash like error response.
Can you help me ...
I have instaled correctly the sensor since 1 month,
I have used my print without problem until now but today,
The sensor is blocked but the Led is lighted, when i use the test command, the sensor dont move , after the test command the sensor flash like error response.
Can you help me ...
- Wed Feb 21, 2018 12:30 pm
- Forum: Geeetech I3 Pro B
- Topic: Correct température for bed
- Replies: 4
- Views: 5602
Re: Correct température for bed
I check tath
Ty
Ty
- Mon Feb 19, 2018 7:08 am
- Forum: Geeetech I3 Pro B
- Topic: Correct température for bed
- Replies: 4
- Views: 5602
Re: Correct température for bed
I have bed level sensor instaled, it's not the z axis the problem but i found some response to my problem,
I up the temp of extrudor and bed but i dont know the Good temp for bed with abs , cause the glass and tape double face retain some heat.
95 degree is good for abs ?
Thank
I up the temp of extrudor and bed but i dont know the Good temp for bed with abs , cause the glass and tape double face retain some heat.
95 degree is good for abs ?
Thank
- Sat Feb 17, 2018 5:47 am
- Forum: Geeetech I3 Pro B
- Topic: Correct température for bed
- Replies: 4
- Views: 5602
Correct température for bed
Goodmorning,
My object realised is all creased after 3 layer, however it was well glue with double face tape,
how can I correctly set the temperature of the bed please ? because it peels off all the time after 3 layer
Thanks
My object realised is all creased after 3 layer, however it was well glue with double face tape,
how can I correctly set the temperature of the bed please ? because it peels off all the time after 3 layer
Thanks
- Sat Feb 17, 2018 1:08 am
- Forum: Geeetech I3 Pro B
- Topic: Level bed sensor on pro b need help
- Replies: 2
- Views: 3997
Re: Level bed sensor on pro b need help
Nothing about this adjustement with the magnet screw on top of the sensor anywhere.
With chance, it happen not too much, but when arrive, i must enter the gcode for stop the alarm and adjust the screw, is it like the screw move itself when extrudor viber.
With chance, it happen not too much, but when arrive, i must enter the gcode for stop the alarm and adjust the screw, is it like the screw move itself when extrudor viber.
- Thu Feb 15, 2018 8:09 am
- Forum: Geeetech I3 Pro B
- Topic: Level bed sensor on pro b need help
- Replies: 2
- Views: 3997
Level bed sensor on pro b need help
hello, I installed correctly the sensor but the tilt tends to hang and activated the alarm (red flashing)
It hangs down, I try to go up or down the screw (magnet), it works but from time to time it still blocks, do you have any tips or a link to correctly configure the sensor screw please ?
thank you
It hangs down, I try to go up or down the screw (magnet), it works but from time to time it still blocks, do you have any tips or a link to correctly configure the sensor screw please ?
thank you
- Fri Nov 25, 2016 11:17 am
- Forum: Stepper Motor
- Topic: Y home dont want move
- Replies: 1
- Views: 4544
Y home dont want move
Bonjour, quand j' appuie sur home pour l' axe y, le lit ne bouge pas.
Pourriez vous m' aider svp ?
Merci
Goodmorning, when I push home for y, y dont move.
I already need to change y and x motor direction and
Endstop x & y too.
But when I test x endstop, the motor wont stop and continue also if ...
Pourriez vous m' aider svp ?
Merci
Goodmorning, when I push home for y, y dont move.
I already need to change y and x motor direction and
Endstop x & y too.
But when I test x endstop, the motor wont stop and continue also if ...
- Sat Nov 12, 2016 1:26 pm
- Forum: Firmware
- Topic: firmware and fix false or true
- Replies: 1
- Views: 4100
firmware and fix false or true
Goodmorning
can you tell me if i must change the firmware in the same time of the change in "configuration.h ?
and upload together or
if i do only one change in configuration.h and i send, the change is effective ?
ty thery much
can you tell me if i must change the firmware in the same time of the change in "configuration.h ?
and upload together or
if i do only one change in configuration.h and i send, the change is effective ?
ty thery much