Hi,
Would like some help. Noticed that if I disconnect power from the Geeetech Prusa i3 Pro C, then turn it back on, the E-steps reset from whatever value I had configured back to 78.74 - which I think is what it initially was configured with. This E-step resetting caused a print to have very off ...
Search found 7 matches
- Sat Apr 15, 2017 5:18 am
- Forum: Firmware
- Topic: E-steps reset after power cut
- Replies: 1
- Views: 3641
- Thu Jan 05, 2017 5:06 am
- Forum: Extruder
- Topic: Thermal Runaway
- Replies: 5
- Views: 12169
Re: Thermal Runaway
HI bang,
I did notice those articles here but they did not seem related to my issue as I don't have bed auto leveling. I did read through the articles but they seemed irrelevant, so I created a new thread. But thanks anyway
I did notice those articles here but they did not seem related to my issue as I don't have bed auto leveling. I did read through the articles but they seemed irrelevant, so I created a new thread. But thanks anyway

- Wed Jan 04, 2017 2:16 am
- Forum: Extruder
- Topic: Thermal Runaway
- Replies: 5
- Views: 12169
Re: Thermal Runaway
An update on the situation:
I have changed the settings in the firmware for the Thermal Runaway protection, I noticed that for the Extruder hotend the temperature was set to 4 deg. allowed change and 40 sec until the Thermal Runaway is initiated. The heatbed had 2 deg. and 20 sec of reaction time ...
I have changed the settings in the firmware for the Thermal Runaway protection, I noticed that for the Extruder hotend the temperature was set to 4 deg. allowed change and 40 sec until the Thermal Runaway is initiated. The heatbed had 2 deg. and 20 sec of reaction time ...
- Fri Dec 30, 2016 12:55 am
- Forum: Extruder
- Topic: Thermal Runaway
- Replies: 5
- Views: 12169
Re: Thermal Runaway
Thanks Cup, for the response and the article reference.
And thanks for the new vocabulary "Mosfet" (I'm Estonian so I have still a lot to learn :D ).
I had a little time to only take measurements of the mosfet, I will be able to possibly add pictures or videos in a few days.
What I did was ...
And thanks for the new vocabulary "Mosfet" (I'm Estonian so I have still a lot to learn :D ).
I had a little time to only take measurements of the mosfet, I will be able to possibly add pictures or videos in a few days.
What I did was ...
- Wed Dec 28, 2016 8:39 am
- Forum: Extruder
- Topic: Thermal Runaway
- Replies: 5
- Views: 12169
Thermal Runaway
Hi,
I have recently finished assembling (started 4 days ago) a "Prusa i3 Pro C Dual Extruder" printer and I am trying to make my first prints. So far there are a few Issues that I can't solve on my own, so I turn to smarter people on forums.
1. (It may be how it works but) a part right above the ...
I have recently finished assembling (started 4 days ago) a "Prusa i3 Pro C Dual Extruder" printer and I am trying to make my first prints. So far there are a few Issues that I can't solve on my own, so I turn to smarter people on forums.
1. (It may be how it works but) a part right above the ...
- Sun Dec 25, 2016 12:42 am
- Forum: Stepper Motor
- Topic: Z axis motors not moving without rods connected
- Replies: 2
- Views: 5864
Re: Z axis motors not moving without rods connected
Hi again,
Further to my previous post, I figured out that the issue was with jumpers, the assembly guide says to only leave the far left jumpers but that was wring, as everything started working after I put all jumpers in.
The only thing now is that some parts of the threaded Z rod are not perfect ...
Further to my previous post, I figured out that the issue was with jumpers, the assembly guide says to only leave the far left jumpers but that was wring, as everything started working after I put all jumpers in.
The only thing now is that some parts of the threaded Z rod are not perfect ...
- Sat Dec 24, 2016 10:01 pm
- Forum: Stepper Motor
- Topic: Z axis motors not moving without rods connected
- Replies: 2
- Views: 5864
Z axis motors not moving without rods connected
Geeetech Prusa I3 pro C dual extruder 3D
Hi forum,
I just yesterday finished assembling the printer and a few issues arise:
1. X axis (should be left to right movement) is unstable and sometimes gets stuck. - I have checked the belts and the smooth rods leveling I also tried oil but it is still ...
Hi forum,
I just yesterday finished assembling the printer and a few issues arise:
1. X axis (should be left to right movement) is unstable and sometimes gets stuck. - I have checked the belts and the smooth rods leveling I also tried oil but it is still ...