Search found 14 matches

by Nyemrinju
Sun Sep 15, 2019 8:25 pm
Forum: Geeetech A30 Series
Topic: Printer stopps at 30mm hight
Replies: 6
Views: 9191

Re: Printer stopps at 30mm hight

So, I have now finished with this printer and bought the Chiron from Anycubic. This prints right away and how he should! Pity about the wasted time and money! :oops:
by Nyemrinju
Sun Sep 01, 2019 8:18 pm
Forum: Geeetech A30 Series
Topic: z axis vibration
Replies: 8
Views: 14737

Re: z axis vibration


Hi,

I am currently facing severe quality issues with my new A30. The prints dont look good compared to the my "old" Mecreator2. Edges of printed objects are not sharp and i have blobs and zits on every print. Maybe the vibration of the z axis are the reason for this? One of the z-rods is making ...
by Nyemrinju
Sat Aug 31, 2019 9:09 pm
Forum: Geeetech A30 Series
Topic: Printer stopps at 30mm hight
Replies: 6
Views: 9191

Re: Printer stopps at 30mm hight

Hi,
the answer took a while (holidays etc). What I noticed now is that both threaded rods when starting up to a height of about 180mm in the upper bearings are about 3-5mm back and forth. From that height, this movement is over. Is that right and wanted? Are the threaded rods possibly bent or the ...
by Nyemrinju
Fri Aug 09, 2019 2:29 am
Forum: Geeetech A30 Series
Topic: Endstop Switch Module
Replies: 4
Views: 6757

Re: Endstop Switch Module

The sales support contacted me. Sending the replacement endstop-switch would cost 20USD! That is too expensive for me! I found a mechanical solution. I carefully removed the plastic top, which contains the switch and the metal tongue, from one of the endstop switch's failed purchases, and then ...
by Nyemrinju
Thu Aug 08, 2019 6:37 pm
Forum: Geeetech A30 Series
Topic: Endstop Switch Module
Replies: 4
Views: 6757

Re: Endstop Switch Module

I contacted the sales support. The answer is not clear. I am directed to the mechanical endstop with the 4 pin connection. That does not help me! It must be possible to tell me how this endstop on the A30 is connected to the existing connector, without the Powersupply housing must be opened! Why is ...
by Nyemrinju
Thu Aug 08, 2019 12:14 am
Forum: Geeetech A30 Series
Topic: Printer stopps at 30mm hight
Replies: 6
Views: 9191

Re: Printer stopps at 30mm hight

I have noticed that the right and left height of the X-axis are adjusted after a few pressure tests. Then the axis moves and the described problem occurs again!
by Nyemrinju
Wed Aug 07, 2019 11:59 pm
Forum: Geeetech A30 Series
Topic: Endstop Switch Module
Replies: 4
Views: 6757

Endstop Switch Module

Hi,
i need a mechanical end stop switch module for the “Geeetech A30 touch screen open source power resuming printer” I bought in Oct. 10th. 2018. I need the module for the Z axis. The plug has 3 pins, which are assigned with 3 wires (red, black and blue). I have already bought some, but at all ...
by Nyemrinju
Wed Jul 03, 2019 9:10 pm
Forum: Geeetech A30 Series
Topic: Printer stopps at 30mm hight
Replies: 6
Views: 9191

Printer stopps at 30mm hight

Hello,
It is not possible to release a print with the part. now rattles at about 30mm the right engine of the z-axis and it moves not higher ...
by Nyemrinju
Sat Dec 01, 2018 3:56 pm
Forum: Geeetech A30 Series
Topic: Disappointing
Replies: 1
Views: 4008

Disappointing

I've got the printer for 2 months now and not a decent print. Each time it continued with printing from any layer with an offset of 3-4mm. The last firmware I installed yesterday (V1.39.62). This also did not improve!
:(
by Nyemrinju
Fri Nov 30, 2018 11:22 pm
Forum: Geeetech A30 Series
Topic: Print is not centered...
Replies: 11
Views: 22415

Re: Print is not centered...

Thx...I will test it!