Search found 51 matches

Go to advanced search

by Chub
Thu May 14, 2020 8:22 pm
Forum: Geeetech A10 Series
Topic: Outer wall /. inner wall connection
Replies: 3
Views: 3873

Re: Outer wall /. inner wall connection

I am running 100% of extruder 1. No mix.
by Chub
Thu May 14, 2020 10:02 am
Forum: Geeetech A10 Series
Topic: Outer wall /. inner wall connection
Replies: 3
Views: 3873

Outer wall /. inner wall connection

Using Cura 4.6.1 on A10M. Why don't I get good connection between the inner and outer wall? I tried increasing over lap and no change
by Chub
Fri Apr 24, 2020 7:38 am
Forum: Geeetech A10 Series
Topic: Frozen X-axis?
Replies: 1
Views: 3215

Frozen X-axis?

I have an A10M. Finished a print. Went to auto home and get this horrific sound.
I am NOT hitting the bed,. checked belt tension and wheels turn free when I disable stepper motor. What else? Hot end carriage grinds and doesn't move. In the X-axis only. Y and Z are fine.
I would upload grinding ...
by Chub
Tue Feb 18, 2020 11:57 pm
Forum: Geeetech A10 Series
Topic: Layer shift and PID test
Replies: 2
Views: 3398

Re: Layer shift and PID test

Z axis moved fine. How do I adjust tightness. It seems fine but I can play around with it. Why doesn't it happen until several layers into printing?
by Chub
Tue Feb 18, 2020 9:35 am
Forum: Geeetech A10 Series
Topic: Layer shift and PID test
Replies: 2
Views: 3398

Layer shift and PID test

Suddenly I am getting layer shift after 5 layers. All of a sudden it is 75% off. I have checked belts tension and wheels. All tight. Now I can't get a print past 5 layer's. Causes?
I thought I would try tune my hotend with M303 auto tune. It ramps temp up and cools down but doesn't report back ...
by Chub
Mon Feb 17, 2020 9:31 am
Forum: Firmware
Topic: How to update the hex firmware via cura
Replies: 19
Views: 52341

Re: How to update the hex firmware via cura

Thank you for the advice. That's why I have dragged my feet on upgrading.
I suddenly am getting huge layer shift after like 5 layers. I have checked belts, bolts for tightness. All seems good. I figured if I had to adjust stuff, I might as well upgrade. I will keep 1.1.8 for now.
Thoughts on layer ...
by Chub
Mon Feb 17, 2020 8:13 am
Forum: Firmware
Topic: How to update the hex firmware via cura
Replies: 19
Views: 52341

Re: How to update the hex firmware via cura

So to upgrade to Marlin. So all I have to do is download configuration files and upgrade through Cura? No Arduino stuff? I am on Marlin 1.1.8. Can I load anyone's A10M config? Is the official Geeetech files 1.1.19 or 2.0?
Hopefully it is that easy. I have read that some people have issues after ...
by Chub
Mon Feb 17, 2020 8:12 am
Forum: Firmware
Topic: How to update the hex firmware via cura
Replies: 19
Views: 52341

Re: How to update the hex firmware via cura

Bernie to upgrading Marlin. So all I have to do is download configuration files and upgrade through Cura? No Arduino stuff? I am on Marlin 1.8. Can I load anyone's A10M config? Is the official Geeetech files 1.19 or 2.0?
Hopefully it is that easy. I have read that some people have issues after ...
by Chub
Sat Feb 15, 2020 10:41 am
Forum: Geeetech A10 Series
Topic: A10M: Do yourself a favor, throw the hot end in the trash
Replies: 10
Views: 17994

Re: A10M: Do yourself a favor, throw the hot end in the trash

What are you starting g-code commands. My start and end are blank.
by Chub
Thu Dec 12, 2019 8:01 am
Forum: Geeetech A10 Series
Topic: E-step or under extrude
Replies: 0
Views: 2627

E-step or under extrude

My prints are very lonely. Is this under extrusions or is there an e step adjustment needed? It is printing sideways so it fits the bed. If it is e-step, how do I adjust?

Go to advanced search