Search found 8 matches
- Wed Mar 27, 2019 6:23 pm
- Forum: Geeetech A10 Series
- Topic: Problem with 3d touch and bed leveling
- Replies: 4
- Views: 6170
Re: Problem with 3d touch and bed leveling
Thank you i will try it.
- Wed Mar 27, 2019 2:21 am
- Forum: Geeetech A10 Series
- Topic: Problem with 3d touch and bed leveling
- Replies: 4
- Views: 6170
Re: Problem with 3d touch and bed leveling
thank you for your answer, but how do I check the deviation and which gcode do I have to use?
- Fri Mar 22, 2019 10:58 pm
- Forum: Geeetech A10 Series
- Topic: Smd fuses
- Replies: 4
- Views: 6375
Re: Smd fuses
I also blew one of my fuses and i found a spare part on Aliexpress, didn´t receive it yet so I can´t tell you if it works. Just search SMD fast blow fuse on Aliexpress and you will find the right thing
- Fri Mar 22, 2019 6:17 pm
- Forum: Geeetech A10 Series
- Topic: Extrusion Problems
- Replies: 5
- Views: 7506
Re: Extrusion Problems
Sorry I didn´t respond, I didn´t see there were responds to my question.
If anyone else has this problem my problem was that the extruder wasn´t tight enough. I bought the metal extruder and now everything works fine again
If anyone else has this problem my problem was that the extruder wasn´t tight enough. I bought the metal extruder and now everything works fine again
- Fri Mar 22, 2019 6:13 pm
- Forum: Geeetech A10 Series
- Topic: Problem with 3d touch and bed leveling
- Replies: 4
- Views: 6170
Problem with 3d touch and bed leveling
Hello there,
I have recently bought a 3d touch sensor for my A10. I have installed the sensor successfully, but the auto bed levelling doesn´t work as expected. The 3d touch measures all points on the plate, but when I print on one side the nozzle seems too high and on the other side it is ...
I have recently bought a 3d touch sensor for my A10. I have installed the sensor successfully, but the auto bed levelling doesn´t work as expected. The 3d touch measures all points on the plate, but when I print on one side the nozzle seems too high and on the other side it is ...
- Tue Feb 12, 2019 10:34 pm
- Forum: Geeetech A10 Series
- Topic: Extrusion Problems
- Replies: 2
- Views: 6650
Extrusion Problems
I have my A10 for two weeks now and everything worked fine in the beginning. During my last print severe underextrusion occured. I cleaned the complete hotend did calibration of the extruder and Bed levelling, but I simply cannot print.
My problem is that hardly any material comes out of the nozzle ...
My problem is that hardly any material comes out of the nozzle ...
- Tue Feb 12, 2019 10:33 pm
- Forum: Geeetech A10 Series
- Topic: Extrusion Problems
- Replies: 5
- Views: 7506
Extrusion Problems
I have my A10 for two weeks now and everything worked fine in the beginning. During my last print severe underextrusion occured. I cleaned the complete hotend did calibration of the extruder and Bed levelling, but I simply cannot print.
My problem is that hardly any material comes out of the nozzle ...
My problem is that hardly any material comes out of the nozzle ...
- Tue Feb 12, 2019 7:17 pm
- Forum: Geeetech A10 Series
- Topic: Geeetech A10 firmware Marlin 1.1.9
- Replies: 78
- Views: 235951
Re: Geeetech A10 firmware Marlin 1.1.9
Search the .ino file in the zip folder and open IT in the Arduino IDE. Open the configurarion.h tab and change the HEATER_0_MAXTEMP and the Bed Maxtemp. Then compile and upload IT via Arduino IDE
If you want a maximum of 250 you habe to Set the temperature to 265 and for the Bed also +15 to your ...
If you want a maximum of 250 you habe to Set the temperature to 265 and for the Bed also +15 to your ...