I have the exact same problem. Even with a large prime tower in Cura the colors are bleeding. If I print white and green, it is very difficult to get a clear white, it always looks greenish.
The main problem I see is with Cura, the prime tower is not clever. In my view each layer in the prime tower ...
Search found 14 matches
- Thu Sep 05, 2019 11:58 pm
- Forum: Geeetech A20M
- Topic: change color not clean !
- Replies: 6
- Views: 9410
- Fri Aug 02, 2019 12:07 am
- Forum: Geeetech A10 Series
- Topic: A10M Clogged nozzle
- Replies: 3
- Views: 5467
Re: A10M Clogged nozzle
Hi William
Thank you for your suggestion. It solved my problem, and my printer is now up and running again
Thank you for your suggestion. It solved my problem, and my printer is now up and running again

- Sat Jul 27, 2019 9:02 pm
- Forum: Geeetech A10 Series
- Topic: A10M Clogged nozzle
- Replies: 3
- Views: 5467
A10M Clogged nozzle
Currently I can only print from extruder 0 (the right sided one) but not from extruder 1. I have tried to press the PLA filament out by hand but it seems to be clogged.
I have looked in the manual for advice as well as in this forum and on Youtube, but no success.
How do I remove the clog?
I have looked in the manual for advice as well as in this forum and on Youtube, but no success.
How do I remove the clog?
- Fri Jul 26, 2019 12:01 am
- Forum: Geeetech A10 Series
- Topic: A10M Color leakage in nozzle?
- Replies: 3
- Views: 4787
Re: A10M Color leakage in nozzle?
To parker1ray:
How does your prime tower look when dual color printing?
Do you get only one color per layer in the tower?
Could you share your settings for the prime tower?
I did increase the tower to 30mm and increased the min filling to 80mm3 for both colors. It did improve the print a little bit ...
How does your prime tower look when dual color printing?
Do you get only one color per layer in the tower?
Could you share your settings for the prime tower?
I did increase the tower to 30mm and increased the min filling to 80mm3 for both colors. It did improve the print a little bit ...
- Tue Jul 23, 2019 11:26 pm
- Forum: Geeetech A10 Series
- Topic: A10M Color leakage in nozzle?
- Replies: 3
- Views: 4787
A10M Color leakage in nozzle?
I have observed a strange behaviour with my new A10M.
Just a little about my setup: I have white PLA in the right extruder (T0) and green PLA in the left extruder (T1). I use Cura 4.1 with a square prime tower of 20mm with minimum filling of 40mm3 for both colors.
I have just printed the two color ...
Just a little about my setup: I have white PLA in the right extruder (T0) and green PLA in the left extruder (T1). I use Cura 4.1 with a square prime tower of 20mm with minimum filling of 40mm3 for both colors.
I have just printed the two color ...
- Tue Jul 23, 2019 9:48 pm
- Forum: Firmware
- Topic: A10M Color leakage in nozzle?
- Replies: 1
- Views: 4064
A10M Color leakage in nozzle?
I have observed a strange behaviour with my new A10M.
Justa little about my setup: I have white PLA in the right extruder (T0) and green PLA in the left extruder (T1). I use Cura 4.1 with a square prime tower of 20mm with minimum filling of 40mm3 for both colors.
I have just printed the two color ...
Justa little about my setup: I have white PLA in the right extruder (T0) and green PLA in the left extruder (T1). I use Cura 4.1 with a square prime tower of 20mm with minimum filling of 40mm3 for both colors.
I have just printed the two color ...
- Tue Jul 23, 2019 4:05 am
- Forum: Geeetech A10 Series
- Topic: A10m Pausing at Purge tower.
- Replies: 14
- Views: 16431
Re: A10m Pausing at Purge tower.
Sorry, the photos didn't load on my iPad.
- Tue Jul 23, 2019 4:02 am
- Forum: Geeetech A10 Series
- Topic: A10m Pausing at Purge tower.
- Replies: 14
- Views: 16431
- Tue Jul 23, 2019 3:59 am
- Forum: Geeetech A10 Series
- Topic: A10m Pausing at Purge tower.
- Replies: 14
- Views: 16431
Re: A10m Pausing at Purge tower.
I have included a photo of the OmNom with the prime tower.
The prime tower has a white ring between the two green ring all the way down to the first layer, but the OmNom is green for the first many layers. So I don’t quite get why the tower isn’t all green for the bottom layers.
By the way I think ...
The prime tower has a white ring between the two green ring all the way down to the first layer, but the OmNom is green for the first many layers. So I don’t quite get why the tower isn’t all green for the bottom layers.
By the way I think ...
- Mon Jul 22, 2019 11:00 pm
- Forum: Geeetech A10 Series
- Topic: A10m Pausing at Purge tower.
- Replies: 14
- Views: 16431
Re: A10m Pausing at Purge tower.
Thank you for your solution to the pausing issue. It has annoyed me ever since I got the A10M. I would never have looked at the z-speed for the solution👌
Maybe you have a solution for my remaining issue: When printning e.g. the two (three with the black eyes) color OmNom, my prime tower always has ...
Maybe you have a solution for my remaining issue: When printning e.g. the two (three with the black eyes) color OmNom, my prime tower always has ...