Search found 15 matches
- Wed Apr 29, 2020 6:12 am
- Forum: A30M
- Topic: Extruder upgrade for A30M
- Replies: 3
- Views: 17363
Re: Extruder upgrade for A30M
I upgrade mine to some trianglelabs bmg clone extruders.
- Fri Apr 17, 2020 4:36 am
- Forum: A30M
- Topic: Layer shifting
- Replies: 15
- Views: 43100
Re: Layer shifting
i adjusted the voltage to 1.2 and still getting layer shifting.
i was looking at the tmc2208 you sell. it comes with heat sink.
The ones in mine right now dont have heat sink..
where they supposed to come with it ???
maybe they are getting too hot because they dont have heat sink ?
i was looking at the tmc2208 you sell. it comes with heat sink.
The ones in mine right now dont have heat sink..
where they supposed to come with it ???
maybe they are getting too hot because they dont have heat sink ?
- Tue Apr 14, 2020 5:12 am
- Forum: A30M
- Topic: Layer shifting
- Replies: 15
- Views: 43100
Re: Layer shifting
The blue ones are with low voltage.
The black ones are with high voltage
The black ones are with high voltage
- Tue Apr 14, 2020 5:11 am
- Forum: A30M
- Topic: Layer shifting
- Replies: 15
- Views: 43100
Layer shifting
I’m getting problems with layer shifting.
I already tightened the belt.
Up the volts on the driver
Lower the volts on the driver
Lower jerk and acceleration
Tried another slicer program
Not sure what else to do.
I already tightened the belt.
Up the volts on the driver
Lower the volts on the driver
Lower jerk and acceleration
Tried another slicer program
Not sure what else to do.
- Sat Feb 29, 2020 12:22 pm
- Forum: A30M
- Topic: Major clog on hot end
- Replies: 5
- Views: 19049
Re: Major clog on hot end
The right side hot end the pointy end was facing up and the left side the pointy end was facing Down
Are they supposed to be like that or both should be facing the same way ?
And if both should be facing same way what way is the right way ??
Are they supposed to be like that or both should be facing the same way ?
And if both should be facing same way what way is the right way ??
- Sat Feb 29, 2020 6:40 am
- Forum: A30M
- Topic: Major clog on hot end
- Replies: 5
- Views: 19049
Major clog on hot end
I had a major clog and had to take the hot end apart.
When I was taking off the hot end throat. I think that’s what is called. There were a copper cap on each side.
On side tho had it installed facing up. The other side had it installed facing down.
Do I need them ?
What are they for ?
What’s the ...
When I was taking off the hot end throat. I think that’s what is called. There were a copper cap on each side.
On side tho had it installed facing up. The other side had it installed facing down.
Do I need them ?
What are they for ?
What’s the ...
- Sat Feb 22, 2020 6:30 pm
- Forum: A30M
- Topic: Z axis dropping when shutting down
- Replies: 4
- Views: 8140
Re: Z axis dropping when shutting down
The z axis is tight and it’s the motor it self. The left motor turning a little bit while it shuts off.
Should I just flash the software ??
Should I just flash the software ??
- Fri Feb 21, 2020 7:18 pm
- Forum: A30M
- Topic: Z axis dropping when shutting down
- Replies: 4
- Views: 8140
Re: Z axis dropping when shutting down
I had one but it broke somehow when my was printing.
I am about to order one right now.
But still why does the left side z axis drops when I shut down the printer ?
Or sometimes if I don’t do nothing it will just drop a little bit.
Just one side does it. It’s weird
I am about to order one right now.
But still why does the left side z axis drops when I shut down the printer ?
Or sometimes if I don’t do nothing it will just drop a little bit.
Just one side does it. It’s weird
- Thu Feb 20, 2020 1:27 pm
- Forum: A30M
- Topic: Z axis dropping when shutting down
- Replies: 4
- Views: 8140
Z axis dropping when shutting down
My A30m z axis only drops from the left side when I shut it down. I have a motor on each side for the z axis rods. But only the left side motor drops after it shuts off. Also if I don’t use the printer for like a minute it the left z axis motors drops by it self a little.
When I start to print ...
When I start to print ...
- Tue Feb 11, 2020 2:22 pm
- Forum: A30M
- Topic: Auto level not working priting from usb
- Replies: 3
- Views: 6164
Re: Auto level not working priting from usb
Does the Mylar sticker just peel off ?
Is it a one time use only or can I peel it off and re install it ?
Want to see what’s causing this. If the Mylar is off or the whole hot bed Metal is off
Is it a one time use only or can I peel it off and re install it ?
Want to see what’s causing this. If the Mylar is off or the whole hot bed Metal is off