My slicer settings

[zhangxueyou]

I use Geeetech Prusa i3B, with 1.75mm filament and 0.3mm diameter nozzle. Slicer software is Slic3r. Attachment is my slicer settings, I got good print with these settings, you can try.
Actually, anyone who uses different kinds of printer, or the same printer with different filament diameter or nozzle diameter, can also refer to this setting. But you have to change some parameters in slic3r, including "filament diameter", "nozzle diameter", "first layer height"(it is as same as nozzle diameter), "other layers height"(I suggest lower than first layer for 0.05-0.1mm).

slicer settings(1.75-0.3).zip

(637.06 KiB) Downloaded 3500 times

How to access slicer setting and slice:
Open Repetier-Host, click "configuration" under "Slicer" tab:

configuration.png (15.29 KiB) Viewed 67994 times

Save change after you change every group of parameters.

save parameters.png (22 KiB) Viewed 67994 times

Click "slice with slic3r" to generate g-code:

slice with slic3r.png (15.88 KiB) Viewed 67994 times

You can save the g-code in SD card to print off-line:

save gcode.png (21.03 KiB) Viewed 67994 times

[zhangxueyou]

You can also load the configuration file too.

slicer config.zip

(1.27 KiB) Downloaded 3361 times

Open slic3r in Repetier Host:

import slicer setting 1.png (46.16 KiB) Viewed 68582 times

import slicer setting 2.png (52.58 KiB) Viewed 68582 times

import slicer setting 3.png (87.36 KiB) Viewed 68582 times

[ingsergio]

Greetings.

Look already sent to print out sero no filament 1.75 abs. Will speed stepper motor extruder?

[zhangxueyou]

Greetings.

Look already sent to print out sero no filament 1.75 abs. Will speed stepper motor extruder?

Sorry, I don't get your point.

[ingsergio]

Saludos zhangxueyou.

Ya estoy imprimiendo. Lo unico es que sale como remontada la figura. A que velocidad maneja el motor del extrusor?

[zhangxueyou]

Saludos zhangxueyou.

Ya estoy imprimiendo. Lo unico es que sale como remontada la figura. A que velocidad maneja el motor del extrusor?

La velocidad de extrusión es 95 mm / s. Se ha establecido en el firmware.
Si desea reducir la velocidad de impresión, Puede girar el saber en la pantalla LCD. Como se puede ver en la tercera línea de la pantalla LCD, "FR 100%" is default printing speed.

Traduzco del Inglés al Español en Google traducir, espero obtendrá mi punto.

[ingsergio]

Greetings.

I now have problems with the 0.3mm nozzle. He was making a solid and suddenly stopped distilling abs. (I was stoppered) disassemble the clean at all (nozzle and part where it passes the filament). Start printing again and still covered. I can do?

[zhangxueyou]

Greetings.

I now have problems with the 0.3mm nozzle. He was making a solid and suddenly stopped distilling abs. (I was stoppered) disassemble the clean at all (nozzle and part where it passes the filament). Start printing again and still covered. I can do?

Cuál es la temperatura al imprimir? Cuándo parar?

[ingsergio]

When this printing varies between 240 and 221.

[zhangxueyou]

When this printing varies between 240 and 221.

¿Puede imprimir con la tarjeta SD?