Geeetech

Hi,
I just assembled the Acrylic Geeetech I3 pro 3D Printer (8mm) I purchased from you.
I followed your instructions and put the printer together with no problems.
I installed all the electronics including the heat sinks on the A4988 driver module and made sure the cooling fans were functioning.
I used a meter to check the PSU (power supply unit) and the electrical connections. All were okay.
I connected the Control Board to my computer and install all the software. All installed properly.
The Repetier-Host software acknowledged the Comm port to the Control Board.

However, when I turned on the PSU one of the A4988 modules started smoking.
I immediately turned off the power and remove the defective drive module.
I restarted the system without the defective module and the Control board lit up with no more smoking.
All the fans turned on and the LCD screen lit up with all black squares and nothing else.
No manual controls are functional and the Repetier-Host software will not send any commands to the 3D printer.
I reset everything and rechecked all the wiring and connections.
Again, I used a meter to check the power supply and it is functioning.
Now the LCD screen is not lit.

My question is :
1. When will you send me replacement components to replace all the electronics except the power supply?

Please respond as soon as possible as I was hoping to buy more of these.
I am a teacher and was setting this up for my classroom.
Thank you for your time and consideration.

I am sorry for your trouble. Could you please tell me your purchase link and your order number?

I have replied through a private email directly to zhangxueyou.

Good luck. I had the same thing happen minus the smoke. Still waiting on tech support for it. Actually about to open a paypal dispute for a refund on the pile of garbage they sent me.

Viziwizard wrote:
I have replied through a private email directly to zhangxueyou.

Sorry, but I have not received any private message or email from you.

Hi,
The information you requested is as follows:
Acrylic Geeetech I3 pro 3D Printer - (On Ebay)
Item #: 231472986888
Transaction #: 1155317357013

The following is the message I sent to the store owner (lemon.wang@geeetech.cn) and the response from them.
From: lemon.wang@geeetech.cn [mailto:lemon.wang@geeetech.cn]
Sent: Sunday, March 29, 2015 10:11 PM
To: cadinn
Subject: Re: Acrylic Geeetech I3 pro 3D Printer

Hi Steve,
Sorry for the inconvenience.
I am sorry that I know little about that, could you pls post your problems on our forum? Then our technical team will solve your problems.
This is the link,
http://www.geeetech.com/forum/viewforum.php?f=14

Thanks in advance.
After you post the problems, pls tell me the link, I will help you follow up with our technical colleague.
I will resend all parts you need to replace after you confirm with my technical colleague.
Appreciate your kindly understanding.
Best regards
Lemon

Hi Lemon,
I received the :
Acrylic Geeetech I3 pro 3D Printer - (On Ebay)
Item #: 231472986888
Transaction #: 1155317357013
purchased from you.
Thank you for the prompt delivery.

I followed your instructions and put the printer together with no problems.
I installed all the electronics including the heat sinks on the A4988 driver module and made sure the cooling fans were functioning.

However, when I powered it up one of the A4988 modules started smoking.
I immediately turned off the power and remove the defective drive module.
I restarted the system without the defective module and the Control board lit up with no more smoking.
All the fans turned on and the LCD screen lit up with all black squares and nothing else.
No controls are functional.
I reset everything and rechecked all the wiring and connections.
Nothing is happening.
Please respond as soon as possible.
I am a teacher and was setting this up for my classroom.
Thank you for your time and consideration.
Steve Ethier


From: lemon.wang@geeetech.cn [mailto:lemon.wang@geeetech.cn]
Sent: Thursday, March 19, 2015 4:06 AM
To: cadinn
Subject: Re: RE: Acrylic Geeetech I3 pro 3D Printer building instruction


Hi Steve,
We have sent the printer to you, you can find the information via this link,
http://www.dhl.com/en/express/tracking. ... &brand=DHL

Hope you receive the package soon.
And thanks in advance for sharing my printer to your friends.
Best regards
Lemon

Get a refund and buy from a respected company. They denied my PayPal refund so I escalated it to a claim.

Viziwizard wrote:Hi,
The information you requested is as follows:
Acrylic Geeetech I3 pro 3D Printer - (On Ebay)
Item #: 231472986888
Transaction #: 1155317357013

The following is the message I sent to the store owner (lemon.wang@geeetech.cn) and the response from them.
From: lemon.wang@geeetech.cn [mailto:lemon.wang@geeetech.cn]
Sent: Sunday, March 29, 2015 10:11 PM
To: cadinn
Subject: Re: Acrylic Geeetech I3 pro 3D Printer

Hi Steve,
Sorry for the inconvenience.
I am sorry that I know little about that, could you pls post your problems on our forum? Then our technical team will solve your problems.
This is the link,
http://www.geeetech.com/forum/viewforum.php?f=14

Thanks in advance.
After you post the problems, pls tell me the link, I will help you follow up with our technical colleague.
I will resend all parts you need to replace after you confirm with my technical colleague.
Appreciate your kindly understanding.
Best regards
Lemon

Hi Lemon,
I received the :
Acrylic Geeetech I3 pro 3D Printer - (On Ebay)
Item #: 231472986888
Transaction #: 1155317357013
purchased from you.
Thank you for the prompt delivery.

I followed your instructions and put the printer together with no problems.
I installed all the electronics including the heat sinks on the A4988 driver module and made sure the cooling fans were functioning.

However, when I powered it up one of the A4988 modules started smoking.
I immediately turned off the power and remove the defective drive module.
I restarted the system without the defective module and the Control board lit up with no more smoking.
All the fans turned on and the LCD screen lit up with all black squares and nothing else.
No controls are functional.
I reset everything and rechecked all the wiring and connections.
Nothing is happening.
Please respond as soon as possible.
I am a teacher and was setting this up for my classroom.
Thank you for your time and consideration.
Steve Ethier


From: lemon.wang@geeetech.cn [mailto:lemon.wang@geeetech.cn]
Sent: Thursday, March 19, 2015 4:06 AM
To: cadinn
Subject: Re: RE: Acrylic Geeetech I3 pro 3D Printer building instruction


Hi Steve,
We have sent the printer to you, you can find the information via this link,
http://www.dhl.com/en/express/tracking. ... &brand=DHL

Hope you receive the package soon.
And thanks in advance for sharing my printer to your friends.
Best regards
Lemon

I am so sorry for replying you so late.
1. We can conclude that A4988 is broken. Please contact customer service , let them send a new one.
2. Please look at the LCD screen at different angle, if you can see words at an angle, then rotate the screw on top-right corner behind LCD clockwise.

There are no letters or black squares. Turning the resistor pot had no effect.

Civiking84 wrote:Get a refund and buy from a respected company. They denied my PayPal refund so I escalated it to a claim.

Please contact customer service.