Hello, i bougth the Acrylic Prusa Mendel I3 a few years ago and today it started to have somw problems with the firmware. It has stopped to move the X and Y axis in positive and the extruder doesnt move. I have cheched changing cables and the controller chips and it seems to be the firmware.
Can ...
Search found 13 matches
- Thu Dec 01, 2016 6:44 am
- Forum: Firmware
- Topic: Acrylic Prusa Mendel I3 Firmware Issue
- Replies: 1
- Views: 4386
- Mon Apr 27, 2015 7:32 pm
- Forum: Others
- Topic: Printer Stops in the middle of the printing
- Replies: 8
- Views: 12984
Re: Printer Stops in the middle of the printing
How do i optimize slicer for this model? Which is the difference between Slic3r and CuraEngine?
- Sat Apr 25, 2015 7:24 am
- Forum: Others
- Topic: Printer Stops in the middle of the printing
- Replies: 8
- Views: 12984
Re: Printer Stops in the middle of the printing
Finally i achieved to print big pieces from the SD card, is a bit annoying, but it works. Now im having another problem with the print quality. This to pieces are supposed to fit together, but the material seem to deform for some reason
- Wed Apr 22, 2015 12:27 am
- Forum: Others
- Topic: Printer Stops in the middle of the printing
- Replies: 8
- Views: 12984
Re: Printer Stops in the middle of the printing
Yes, Z axis seem to be good now, it still makes some nioses and jams passing the 10 cm height but i wont be printing that height. I will try to print from an SD card, how do i save the slicing to a SD card? i would rather not prefer to do it, because i will miss the info from the Repeties Host so if ...
- Wed Apr 22, 2015 12:23 am
- Forum: Extruder
- Topic: Fillament load problem
- Replies: 2
- Views: 4816
Re: Fillament load problem
I dissassembled the mk8 extruder fna and it resulted that the gears were misaligned: i correctedit and it works normal now.
- Tue Apr 21, 2015 9:50 am
- Forum: Others
- Topic: Printer Stops in the middle of the printing
- Replies: 8
- Views: 12984
Printer Stops in the middle of the printing
Acrylis Prusa i3. I've been recently printing small pieces and it works fin, but when i try to print pieces that cos most than an hour it suddenly stops working after 40 minutes or so. When it stops it gives no error message, the LCD and Repetier Host shows that the print stills been made, but the ...
- Tue Apr 21, 2015 1:39 am
- Forum: Others
- Topic: Printer Stops in the middle of the printing
- Replies: 8
- Views: 12984
Mechanical problem Z axis
I've been printing with the Acrylic Prusa I3 foe a week now and im having a problem with the Z axis. It prints well (Had problems with the extruder that i already solved) but qhen it reaches 2 cm in Z axis both motor jams and doesnt come up. How can i calibrate? Is it due to bad pieces or i mounted ...
- Thu Apr 16, 2015 7:16 pm
- Forum: Extruder
- Topic: Fillament load problem
- Replies: 2
- Views: 4816
Fillament load problem
i've tried to load the fillament in the extruder, it heats up good, but the motor jams and cant load it up. If i pull the fillament back, the motor works normally
- Wed Apr 15, 2015 7:08 pm
- Forum: Software
- Topic: Software/Firmware installation
- Replies: 5
- Views: 12499
Re: Software/Firmware installation
I've tried to upload the code and gives me this error:
avrdude: ser_open(): can't open device "\\.\COM3": Access denied.
avrdude: ser_drain(): read error: Controlador no válido.
avrdude: ser_open(): can't open device "\\.\COM3": Access denied.
avrdude: ser_drain(): read error: Controlador no válido.
- Wed Apr 15, 2015 6:40 pm
- Forum: Software
- Topic: Software/Firmware installation
- Replies: 5
- Views: 12499
Re: Software/Firmware installation
I have further tried with an updated version of arduino and it stops giving me taht error, but it shows this whe i try to verify the code:
Arduino:1.6.0 (Windows 7), Placa:"Arduino Mega or Mega 2560, ATmega2560 (Mega 2560)"
sketch_apr15a.cpp.o: In function `loop':
/Arduino/sketch_apr15a.ino:1 ...
Arduino:1.6.0 (Windows 7), Placa:"Arduino Mega or Mega 2560, ATmega2560 (Mega 2560)"
sketch_apr15a.cpp.o: In function `loop':
/Arduino/sketch_apr15a.ino:1 ...