My machine does not have the option to store.William wrote:Hi,after everytime you change the value of Xsteps and Ysteps setting ,you need to store the memory at Main>Control>Store memory.
Search found 7 matches
- Thu May 25, 2017 9:57 am
- Forum: Firmware
- Topic: How to install the firmware for GT2560
- Replies: 141
- Views: 717818
Re: How to install the firmware for GT2560
- Wed May 24, 2017 2:15 pm
- Forum: Firmware
- Topic: How to install the firmware for GT2560
- Replies: 141
- Views: 717818
Re: How to install the firmware for GT2560
OK, I'm lost.
I have my printer up and working, just fine. I want to save the Xsteps and Ysteps setting that I got after calibrating but every time I power down the machine it loses the values I put in.
Where, in the firmware, do I update those values?
Prusa i3 model with the GT2560 board ...
I have my printer up and working, just fine. I want to save the Xsteps and Ysteps setting that I got after calibrating but every time I power down the machine it loses the values I put in.
Where, in the firmware, do I update those values?
Prusa i3 model with the GT2560 board ...
- Sun Apr 23, 2017 4:44 am
- Forum: Discuss & Help
- Topic: Need Help with GT2560 Rev A
- Replies: 6
- Views: 13583
Re: Need Help with GT2560 Rev A
Are you sure you have the LED display and LED input connected correctly?
You shouldn't have so many symptoms unless something is swapped wrong.
You shouldn't have so many symptoms unless something is swapped wrong.
- Sun Apr 23, 2017 4:40 am
- Forum: Discuss & Help
- Topic: Problem with a I3 ProB
- Replies: 5
- Views: 9988
Re: Problem with a I3 ProB
Hi,
One advice i learn from the geeetech printer : prepare to have multiple "upload" of your firmware to the printer.
basicly, you will need to download the Firmware from the geeetech forum (http://www.geeetech.com/forum/viewtopic.php?f=20&t=17046)
Then, upload it, it should be the one you need ...
One advice i learn from the geeetech printer : prepare to have multiple "upload" of your firmware to the printer.
basicly, you will need to download the Firmware from the geeetech forum (http://www.geeetech.com/forum/viewtopic.php?f=20&t=17046)
Then, upload it, it should be the one you need ...
- Sun Apr 23, 2017 3:29 am
- Forum: Extruder
- Topic: Extruder won't work
- Replies: 6
- Views: 12444
Re: Extruder won't work
Hi, I've recently bought a prusa i3c with dual extruder and set it up completely to have it working. sadly I've got some problems with the extruder stepper, which no matter what i try, it does not move.
What I've done so far is:
-Switching and plugging in the X-axis (the motor runs smoothly ...
What I've done so far is:
-Switching and plugging in the X-axis (the motor runs smoothly ...
- Sun Apr 23, 2017 3:00 am
- Forum: Stepper Motor
- Topic: Steper motors don't work
- Replies: 2
- Views: 6485
Re: Steper motors don't work
Sorry, duplicate post.
- Sun Apr 23, 2017 3:00 am
- Forum: Stepper Motor
- Topic: Steper motors don't work
- Replies: 2
- Views: 6485
Re: Steper motors don't work
It sounds like your stepper motor wires aren't configured properly and your stepper isn't sequencing.
If motors run in reverse, resequence all wires. If it jolts, like you say, you probably need to switch two wires. I can't help you with which two to swap because there are too many possibilities ...
If motors run in reverse, resequence all wires. If it jolts, like you say, you probably need to switch two wires. I can't help you with which two to swap because there are too many possibilities ...