Have you closed ANY other program that can connect to the printer ?
Cura / Slic3r etc will stop you from connecting if they're open.
Gerry
Search found 104 matches
- Mon Aug 03, 2020 1:34 am
- Forum: Geeetech I3 Pro B
- Topic: Printer not connecting
- Replies: 1
- Views: 3350
- Wed Jul 29, 2020 6:02 am
- Forum: Geeetech I3 Pro B
- Topic: Leveling Problem what do i wrong
- Replies: 2
- Views: 5217
Re: Leveling Problem what do i wrong
Hi,
Without knowing which version of the firmware you're using...
When I installed my firmware, I started out with a BL Touch.
I used the firmware Marlin-1.1.9_bugfixes_02102019 given by wwysocki...
It ran 1st time for me.
https://www.geeetech.com/forum/viewtopic.php?f=66&t=62412#p90623
From memory ...
Without knowing which version of the firmware you're using...
When I installed my firmware, I started out with a BL Touch.
I used the firmware Marlin-1.1.9_bugfixes_02102019 given by wwysocki...
It ran 1st time for me.
https://www.geeetech.com/forum/viewtopic.php?f=66&t=62412#p90623
From memory ...
- Wed Jul 29, 2020 5:50 am
- Forum: Geeetech I3 Pro B
- Topic: I3 Pro B Retraction impossible
- Replies: 14
- Views: 15811
Re: I3 Pro B Retraction impossible
Hi Bugsia,
Without knowing the details - as you've not given us the material you're using, temps or print speed...
I'll have a guess at where I'd start looking.
1) I'd look at the nozzle/throat tube interface...
Is there a gap between the throat tube and nozzle inside the heater block ? - They ...
Without knowing the details - as you've not given us the material you're using, temps or print speed...
I'll have a guess at where I'd start looking.
1) I'd look at the nozzle/throat tube interface...
Is there a gap between the throat tube and nozzle inside the heater block ? - They ...
- Sun Jul 19, 2020 7:58 am
- Forum: Geeetech I3 Pro B
- Topic: Problems with configuration of 3DTouch Auto Leveling Sensor
- Replies: 8
- Views: 8670
Re: Problems with configuration of 3DTouch Auto Leveling Sensor
Hi Jose,
The menu system allows you to set the 3D Touch Z offset.
Scroll down to 'Control' and select.
Scroll to 'Motion' and select.
The first menu option is the 3D Touch Z offset (It is on my machine ! )
Select and turn the wheel to set the required value.
IMPORTANT...
The go to 'Control' again ...
The menu system allows you to set the 3D Touch Z offset.
Scroll down to 'Control' and select.
Scroll to 'Motion' and select.
The first menu option is the 3D Touch Z offset (It is on my machine ! )
Select and turn the wheel to set the required value.
IMPORTANT...
The go to 'Control' again ...
- Fri Jul 17, 2020 11:49 am
- Forum: Geeetech I3 Pro B
- Topic: Need advice: Geeetech Prusa i3 Pro B or Creality Ender 3?
- Replies: 3
- Views: 6575
Re: Need advice: Geeetech Prusa i3 Pro B or Creality Ender 3?
Hi Jessy,
You're going to have to mess around with the ender 3 to get it working as well !
Printers like this are NOT 'Plug and play' - It's not as simple as printing a word document with an ink-jet printer !
You will have to learn how to tweak all the settings in your slicer program to get good ...
You're going to have to mess around with the ender 3 to get it working as well !
Printers like this are NOT 'Plug and play' - It's not as simple as printing a word document with an ink-jet printer !
You will have to learn how to tweak all the settings in your slicer program to get good ...
- Fri Jul 17, 2020 11:41 am
- Forum: Geeetech I3 Pro B
- Topic: Geeetech I3 ProB, printing in the air??
- Replies: 3
- Views: 4793
Re: Geeetech I3 ProB, printing in the air??
Hi Juan / Gini
So you've checked the bed and it is level...
When you 'Home' the printer, it goes to the correct height - ie you check the nozzle/bed position with a piece of paper under the nozzle.
The problem arises when you start a print ???
One area could be the gcode ?
The first layer of the ...
So you've checked the bed and it is level...
When you 'Home' the printer, it goes to the correct height - ie you check the nozzle/bed position with a piece of paper under the nozzle.
The problem arises when you start a print ???
One area could be the gcode ?
The first layer of the ...
- Fri Jul 17, 2020 11:28 am
- Forum: Geeetech I3 Pro B
- Topic: Problems with configuration of 3DTouch Auto Leveling Sensor
- Replies: 8
- Views: 8670
Re: Problems with configuration of 3DTouch Auto Leveling Sensor
Hi Jlamador,
-7.39 sounds like a high/low number !
I've used a BL Touch since I first built my ProB - It works flawlessly.
When I installed the BL Touch, I had to make sure that when extended, the pin was lower than the nozzle tip - but when in the up position, the pin was above the nozzle... I ...
-7.39 sounds like a high/low number !
I've used a BL Touch since I first built my ProB - It works flawlessly.
When I installed the BL Touch, I had to make sure that when extended, the pin was lower than the nozzle tip - but when in the up position, the pin was above the nozzle... I ...
- Fri Jul 17, 2020 10:54 am
- Forum: Geeetech I3 Pro B
- Topic: Plastic tube near the hot end needs replacement — need help
- Replies: 4
- Views: 6465
Re: Plastic tube near the hot end needs replacement — need help
Hi Suvl,
Well that looks grim !
I've never had to put any torque at all into the throat tube when changing.
I have found that once I've taken it all apart, I can screw the tube up into the extruder just with fingers...
I then do the same with the heater block.
I check that the nozzle can touch the ...
Well that looks grim !
I've never had to put any torque at all into the throat tube when changing.
I have found that once I've taken it all apart, I can screw the tube up into the extruder just with fingers...
I then do the same with the heater block.
I check that the nozzle can touch the ...
- Mon Jul 13, 2020 11:37 pm
- Forum: Geeetech I3 Pro B
- Topic: Plastic tube near the hot end needs replacement — need help
- Replies: 4
- Views: 6465
Re: Plastic tube near the hot end needs replacement — need help
Go on Amazon/Ebay depending on preference...
Type 'Throat tube'
Get something like this...
40mm will work on your proB
https://www.amazon.co.uk/IZOKEE-Extruder-Throat-Nozzle-Print-Makerbot/dp/B06XZ6W61J/ref=sxts_sxwds-bia-wc-p13n2_0?cv_ct_cx=throat+tube&dchild=1&keywords=throat+tube&pd_rd_i ...
Type 'Throat tube'
Get something like this...
40mm will work on your proB
https://www.amazon.co.uk/IZOKEE-Extruder-Throat-Nozzle-Print-Makerbot/dp/B06XZ6W61J/ref=sxts_sxwds-bia-wc-p13n2_0?cv_ct_cx=throat+tube&dchild=1&keywords=throat+tube&pd_rd_i ...
- Fri Jun 05, 2020 6:17 am
- Forum: Geeetech I3 Pro B
- Topic: Réglages Cura avec Geeetech I3 Pro B
- Replies: 4
- Views: 7583
Re: Réglages Cura avec Geeetech I3 Pro B
Hi Marc,
I always print from the SD card as I would hate for a glitch in the computer ruining an 8 hour print just before the end...
I always print with no usb connection between the computer and printer.
Case in point being that I've just typed a very long answer to your questions here - and then ...
I always print from the SD card as I would hate for a glitch in the computer ruining an 8 hour print just before the end...
I always print with no usb connection between the computer and printer.
Case in point being that I've just typed a very long answer to your questions here - and then ...