Search found 13 matches

by 3dralf
Thu Mar 21, 2019 6:46 pm
Forum: Geeetech A10 Series
Topic: Geeetech A10M get rid off 3D touch sensor
Replies: 3
Views: 5578

Re: Geeetech A10M get rid off 3D touch sensor

Tried now the 1.1.9 marlin

The problem G28 always homes about 8mm above the bed

M211 S0 - softwarendstopp disabled
leveled
G92 Z0 - Z to 0
M500 - remember this
M211 S1 - softwareendstop enabled
G1 Z10 - 10Up
G1 Z0 works now but if
G28 then nozzle is 8mm above the Bed, Display says Z 0
Must i ...
by 3dralf
Thu Mar 21, 2019 5:52 pm
Forum: Configuration Profiles Sharing
Topic: A10M Simplify3d Settings
Replies: 5
Views: 31525

Re: A10M Simplify3d Settings

sorry for the late reply,
S3D send me a profile, that works

attached
by 3dralf
Thu Mar 21, 2019 5:48 pm
Forum: Geeetech A10 Series
Topic: Geeetech A10M get rid off 3D touch sensor
Replies: 3
Views: 5578

Geeetech A10M get rid off 3D touch sensor

I want to disable the touch sensor.

Installed a marlin 118 without Touch

But it'll not work

EEProm deleted
Leveled with a peace of paper,
after G28 the nozzle is 8mm above the bed ?!?!?

M211 S0 - softwarendstopp disabled
leveled
G92 Z0 - Z to 0
M500 - remember this
M211 S1 - softwareendstop ...
by 3dralf
Sun Jan 27, 2019 9:08 pm
Forum: Geeetech A10 Series
Topic: Can't print a thing
Replies: 48
Views: 101900

Re: Can't print a thing

I have also many prob printing with a10m

only the first print, two colored dog from sd, was great

What slicer do you use?

I'm trying to print something with s3d 4.1.1
I can print with extruder 1, printing with extruder2 gives the error 104 wrong extruder, sometimes also error 109.
Same error ...
by 3dralf
Tue Jan 15, 2019 1:21 pm
Forum: Geeetech A10 Series
Topic: A10M Extruder Fans very very loud!!!
Replies: 4
Views: 9158

Re: A10M Extruder Fans very very loud!!!

Problem isn't to find the FAN Control, problem is that you can not control the fanspeed even not over the display.
There is no faster or slower reaction by the fan.
by 3dralf
Sun Jan 13, 2019 7:45 pm
Forum: Geeetech A10 Series
Topic: A10M Extruder Fans very very loud!!!
Replies: 4
Views: 9158

Re: A10M Extruder Fans very very loud!!!

I found no way to lower the Speed at cura or s3d.
Does not work.

I'll install 2 * 12V Silent Coolteks at one 24V line, cause teh A10m has 24V Fans.
Therefore i must modify Printhead or find on @ Thingiverse
by 3dralf
Sun Jan 13, 2019 6:49 pm
Forum: Configuration Profiles Sharing
Topic: A10M Simplify3d Settings
Replies: 5
Views: 31525

Re: A10M Simplify3d Settings

Thanks, i'll take a look at it,
but since i'm using S3d also for my Any i would prefere to use S3d for all of my printers
by 3dralf
Sun Jan 13, 2019 6:29 pm
Forum: Geeetech A10 Series
Topic: A10M - Merlin V2 - Leveling BL Touch
Replies: 3
Views: 7098

A10M - Merlin V2 - Leveling BL Touch

I'd tried ist hours but the nozzel is always to near to the bed
I found this as a discription to level BL Touch

; preheat for working temperatures
M502 ; optionally reset to firmware settings
M500; save
M851 Z0 ; reset any z-offset
G28 ; home all
G1 X117 Y117 ; move nozzle in center
M211 S0 ...
by 3dralf
Fri Jan 11, 2019 7:58 pm
Forum: Configuration Profiles Sharing
Topic: A10M Simplify3d Settings
Replies: 5
Views: 31525

A10M Simplify3d Settings

I've many Problems to using Simplify3d to print with only one filement, left or right side.
Are there somewhere some settings for Simplify3d ?