Search found 13 matches

by Alxo
Mon Mar 18, 2019 1:53 am
Forum: Geeetech A10 Series
Topic: I can't start printing!!
Replies: 10
Views: 117586

Re: I can't start printing!! HELP ME!!

sss wrote: Sun Mar 17, 2019 12:16 pm
Alxo wrote: Sun Mar 17, 2019 12:28 am Give the knob a gently push and you will see the menu, select prepare and then auto-home
Well, holding and turning the knob does not make the menu selection on the panel.
Hold? It is a push, just as a regular button
by Alxo
Mon Mar 18, 2019 1:52 am
Forum: Geeetech A10 Series
Topic: Problems with bed in A10
Replies: 5
Views: 11126

Re: Problems with bed in A10

I only use PLA and I've never printed above 60 and usually I use 50, I don't think it is a temperature problem. I have always cleaned it with 96º ethilic alcohol and a cotton cloth, nothing else, yesterday I bought isopropilic alcohol as recommended.

As I said it seems to be an obgoing process even ...
by Alxo
Sun Mar 17, 2019 9:23 pm
Forum: Geeetech A10 Series
Topic: Problems with bed in A10
Replies: 5
Views: 11126

Re: Problems with bed in A10

I attach a picture of the bed. I insist that I'm not cleaning it hot, I did a couple of times at the very beginning

Image
by Alxo
Sun Mar 17, 2019 1:25 am
Forum: Geeetech A10 Series
Topic: Problems with bed in A10
Replies: 5
Views: 11126

Re: Problems with bed in A10



I have observed 2 different problems:
- I've just started printing, however the bed seems to be losing its skin and looks like very old. Is it a problem with the bed, with my settings or that my nozzle is too low and scratches the skin? Should I worry about it or it is just aesthetic?I couldn't ...
by Alxo
Sun Mar 17, 2019 12:46 am
Forum: Geeetech A10 Series
Topic: Problems with bed in A10
Replies: 5
Views: 11126

Problems with bed in A10

I have observed 2 different problems:
- I've just started printing, however the bed seems to be losing its skin and looks like very old. Is it a problem with the bed, with my settings or that my nozzle is too low and scratches the skin? Should I worry about it or it is just aesthetic?I couldn't get ...
by Alxo
Sun Mar 17, 2019 12:28 am
Forum: Geeetech A10 Series
Topic: I can't start printing!!
Replies: 10
Views: 117586

Re: I can't start printing!! HELP ME!!

Give the knob a gently push and you will see the menu, select prepare and then auto-home
by Alxo
Wed Mar 13, 2019 7:22 pm
Forum: Geeetech A10 Series
Topic: A10M upgrade to 2 extruder 2 nozzle setup
Replies: 40
Views: 65819

Re: A10M upgrade to 2 extruder 2 nozzle setup

This thread is very interesting. Currently, I am learning how to control my A10 but I have a second hot end, which I was thinking of using to be able to combine 2 different filaments. I think I only need a second extruder motor and then it should not be a major issue to configure the second nozzle ...
by Alxo
Tue Mar 12, 2019 9:42 pm
Forum: Geeetech A10 Series
Topic: A10 with Marlin 1.1.8 not printing after 3dTouch upgrade
Replies: 4
Views: 8675

Re: A10 with Marlin 1.1.8 not printing after 3dTouch upgrade


Update,

I switch back to the Firmware without 3dtouch and no all worked well as before :!:

So there must be a bug at the Firmware with 3d touch :cry:

BR Harald


I had the same problem, use Arduino IDE 1.8.5 to upload the firmware you can find in the official thread (I haven't tried later ...
by Alxo
Tue Mar 12, 2019 9:40 pm
Forum: Firmware
Topic: Firmware for geeetech 3D printers
Replies: 388
Views: 16826121

Re: Firmware for geeetech 3D printers

Using Arduino 1.8.5 was the answer. I managed to use the printer with the BL Touch. Now I'm fighting to get the proper settings of the printer.
by Alxo
Mon Mar 11, 2019 5:08 pm
Forum: Firmware
Topic: Firmware for geeetech 3D printers
Replies: 388
Views: 16826121

Re: Firmware for geeetech 3D printers

William wrote: Mon Mar 11, 2019 2:21 pm Hi,alxo
I strongly suggest checking the "Note" again.
Try to upload it via Arduino IDE 1.8.5
Thanks for the reply. I have the 1.8.8. I'll try again with the 1.8.5