HI
Thanks i will try. But as i bought this printer from a 3rd party and not directly from Geeetech i am not sure that Geeetech would replace the board.
And its not just the board its also the cable from the PSU that have the male end of the plug.
Search found 6 matches
- Fri Jun 12, 2020 11:07 pm
- Forum: Geeetech Delta Series
- Topic: Faulty power plug
- Replies: 3
- Views: 14517
- Thu Jun 11, 2020 11:47 pm
- Forum: Geeetech Delta Series
- Topic: Faulty power plug
- Replies: 3
- Views: 14517
Faulty power plug
Had an issue where i got home to failed print and after i removed everything and wanted to start over i found that the bed would not heat up.
Then i had a closer look at the board and found that the PSU plug was all burned on one of the 12volt rails.
now i have to locate new plugs and solder a new ...
Then i had a closer look at the board and found that the PSU plug was all burned on one of the 12volt rails.
now i have to locate new plugs and solder a new ...
- Fri Jun 05, 2020 8:31 pm
- Forum: Geeetech Delta Series
- Topic: [Solved] Geeetech G2S problems after firmware upload
- Replies: 5
- Views: 16657
Re: Geeetech G2S problems after firmware upload
Seems like i have fixed it...
Thanks to all the information on your forum WOOOHOOOO!!!
needed to clear the EEPROM with GCODE M502 and all is well

Thanks to all the information on your forum WOOOHOOOO!!!
needed to clear the EEPROM with GCODE M502 and all is well



- Fri Jun 05, 2020 7:44 pm
- Forum: Geeetech Delta Series
- Topic: [Solved] Geeetech G2S problems after firmware upload
- Replies: 5
- Views: 16657
Re: Geeetech G2S problems after firmware upload
OHHHHH!!!! *BEEEP** ARGGGHHH!!! :oops: :oops: :oops: :oops: CRAP!!
Is it possible that the board could have been damaged by a wrong firmware.
I just remembered that i when i created the repetier firmware that i at first selected a board that where RAMPS 1.4 compatible.
when i uploaded the firmware ...
Is it possible that the board could have been damaged by a wrong firmware.
I just remembered that i when i created the repetier firmware that i at first selected a board that where RAMPS 1.4 compatible.
when i uploaded the firmware ...
- Fri Jun 05, 2020 6:42 pm
- Forum: Geeetech Delta Series
- Topic: [Solved] Geeetech G2S problems after firmware upload
- Replies: 5
- Views: 16657
Re: Geeetech G2S problems after firmware upload
The motors are rotating just very very slow
if i upload the repetier firmware they move like they should.
that firmware how ever have a problem with the extruder and other stuff how ever there is nothing wrong with the motors or wires to the motors.
when i upload the standard firmware that always ...
if i upload the repetier firmware they move like they should.
that firmware how ever have a problem with the extruder and other stuff how ever there is nothing wrong with the motors or wires to the motors.
when i upload the standard firmware that always ...
- Fri Jun 05, 2020 4:29 pm
- Forum: Geeetech Delta Series
- Topic: [Solved] Geeetech G2S problems after firmware upload
- Replies: 5
- Views: 16657
[Solved] Geeetech G2S problems after firmware upload
Hi
I am having problems with my G2S printer
Last night i updated the firmware on my printer via arduino and nothing special there.
The change was the name shown in the display from Geeetech to my own name.
But after the update and all looked good the printer have started to do weird stuff.
I have ...
I am having problems with my G2S printer
Last night i updated the firmware on my printer via arduino and nothing special there.
The change was the name shown in the display from Geeetech to my own name.
But after the update and all looked good the printer have started to do weird stuff.
I have ...