Connection 3DTouch sur Rostock 301 Modifié
Posted: Sat Aug 26, 2017 3:00 am
Hello,
Bonjour,
You can find the original text translated into English following this original French text.
Vous trouverez le texte original traduit en anglais à la suite du présent texte original en français.
Comme je ne peux imprimer avec la tête diamant à trois (3) filaments, je l'ai remplacé par une tête chauffante mono filament avec ventilateur et une nouvelle fixation. Voir le détail des pièces et modification sur la page Web suivante :
http://forums.reprap.org/read.php?178,781375
Maintenant, comme la tête d'impression est beaucoup plus petite, je voudrais installer un capteur de nivellement Geeetech 3DTouch acheté en septembre 2016 sur cette Geeetech Rostock 301 modifiée.
Pourriez-vous m'indiquer comment connecter votre capteur de nivellement Geeetech 3DTouch sur votre carte contrôleur ou sur votre carte de l'extrudeur de votre imprimante 3D Geeetech Rostock 301 modifié et comment la configurer (logiciel et matériel) pour son utilisation avant chaque impression avec Repetier-Host ?
Cordialement,
L'ami René
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Hello,
Excuse me, I am unilingual francophone and I use Google translator to translate the texts of the forum in French and to write to you in English. Thank you for your understanding and your indulgence for these texts translated mechanically!
Since I can not print with diamond head with three (3) filaments, I replaced it with a heating head mono filament with fan and a new fixing. See details of parts and modification on the following web page:
http://forums.reprap.org/read.php?178,781375
Now, as the print head is much smaller, I would like to install a Geeetech 3DTouch leveling sensor purchased in September 2016 on this modified Geeetech Rostock 301.
Could you tell me how to connect your Geeetech 3DTouch leveling sensor to your Geeetech Rostock 301 3D Controller card or extruder card and how to configure it (software and hardware) for use before each print job with Repetier-Host?
Cordially,
The friend René
Bonjour,
You can find the original text translated into English following this original French text.
Vous trouverez le texte original traduit en anglais à la suite du présent texte original en français.
Comme je ne peux imprimer avec la tête diamant à trois (3) filaments, je l'ai remplacé par une tête chauffante mono filament avec ventilateur et une nouvelle fixation. Voir le détail des pièces et modification sur la page Web suivante :
http://forums.reprap.org/read.php?178,781375
Maintenant, comme la tête d'impression est beaucoup plus petite, je voudrais installer un capteur de nivellement Geeetech 3DTouch acheté en septembre 2016 sur cette Geeetech Rostock 301 modifiée.
Pourriez-vous m'indiquer comment connecter votre capteur de nivellement Geeetech 3DTouch sur votre carte contrôleur ou sur votre carte de l'extrudeur de votre imprimante 3D Geeetech Rostock 301 modifié et comment la configurer (logiciel et matériel) pour son utilisation avant chaque impression avec Repetier-Host ?
Cordialement,
L'ami René
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Hello,
Excuse me, I am unilingual francophone and I use Google translator to translate the texts of the forum in French and to write to you in English. Thank you for your understanding and your indulgence for these texts translated mechanically!
Since I can not print with diamond head with three (3) filaments, I replaced it with a heating head mono filament with fan and a new fixing. See details of parts and modification on the following web page:
http://forums.reprap.org/read.php?178,781375
Now, as the print head is much smaller, I would like to install a Geeetech 3DTouch leveling sensor purchased in September 2016 on this modified Geeetech Rostock 301.
Could you tell me how to connect your Geeetech 3DTouch leveling sensor to your Geeetech Rostock 301 3D Controller card or extruder card and how to configure it (software and hardware) for use before each print job with Repetier-Host?
Cordially,
The friend René