Ok, so the fan works now, or just turns on.
I can not get the extruder to a temperature above 220 degrees. As such I can not print with it - WHY WILL IT NOT GO HOT ENOUGH TO DO ANYTHING WITH!!!!
PROVIDE SUPPORT OR I WILL REQUEST A REFUND
please advise
Search found 15 matches
- Fri Jul 03, 2015 10:23 pm
- Forum: Extruder
- Topic: Upgrading to Bowden Extruder
- Replies: 9
- Views: 16876
- Thu Jul 02, 2015 7:43 pm
- Forum: Extruder
- Topic: Upgrading to Bowden Extruder
- Replies: 9
- Views: 16876
Re: Upgrading to Bowden Extruder
Well the fan is where it came pre-mounted, having said that it is not wired as you provided a fan with a 2 pin fan knowing I have a 3 pin controller. So I have now tried the other extruder I purchased to see if I had a bad one and get the same results.
Please advise or replace the two extruder ...
Please advise or replace the two extruder ...
- Wed Jul 01, 2015 7:44 pm
- Forum: Extruder
- Topic: Upgrading to Bowden Extruder
- Replies: 9
- Views: 16876
Re: Upgrading to Bowden Extruder
I can not get the temp to go passed 215, Do you think we have a bad extruder?
Please advise
Please advise
- Tue Jun 30, 2015 10:26 am
- Forum: Extruder
- Topic: Upgrading to Bowden Extruder
- Replies: 9
- Views: 16876
Re: Upgrading to Bowden Extruder
Ok,
That said it looks like I can not get the extruder to extrude filament then. It goes through the stepper motor ok but will not extrude. I cannot even force push the filament into the head it seems to either be blocked or not hot enough to melt the filament.
Please advise,
Jason
That said it looks like I can not get the extruder to extrude filament then. It goes through the stepper motor ok but will not extrude. I cannot even force push the filament into the head it seems to either be blocked or not hot enough to melt the filament.
Please advise,
Jason
- Mon Jun 29, 2015 8:01 pm
- Forum: Extruder
- Topic: Upgrading to Bowden Extruder
- Replies: 9
- Views: 16876
Upgrading to Bowden Extruder
I purchased the -Assembled JIETAI GT9L Extruder- and would like to switch out the stock extruder on my prusa I3. Would you please give me the firmware update that I would need for it?
I have this control board GT2560 3D printer controller board.
Thanks
I have this control board GT2560 3D printer controller board.
Thanks
- Tue Jun 16, 2015 11:26 am
- Forum: LCD Panel
- Topic: LCD 12864 with GT2560
- Replies: 29
- Views: 72377
LCD 12864 with GT2560
How do I utilize the LCD 12864 with the GT2560 Controller?
Currently I am using the standard LCD,
In the technical specs it lists the ability to use both monitors.
Please advise
Currently I am using the standard LCD,
In the technical specs it lists the ability to use both monitors.
Please advise
- Tue Jun 16, 2015 9:20 am
- Forum: Control Board
- Topic: Y- Axis Failing
- Replies: 17
- Views: 22001
Re: Y- Axis Failing
Loading via the lower version seemed to work,
I also have a problem with the slicer
I attached a photo of the issue
Please advise
I also have a problem with the slicer
I attached a photo of the issue
Please advise
- Mon Jun 15, 2015 7:29 pm
- Forum: Control Board
- Topic: Y- Axis Failing
- Replies: 17
- Views: 22001
Re: Y- Axis Failing
1.6.4
- Mon Jun 15, 2015 11:08 am
- Forum: Control Board
- Topic: Y- Axis Failing
- Replies: 17
- Views: 22001
Re: Y- Axis Failing
All of the files are loaded into audrinio, 73 total
- Mon Jun 15, 2015 9:37 am
- Forum: Control Board
- Topic: Y- Axis Failing
- Replies: 17
- Views: 22001
Re: Y- Axis Failing
I got the error while trying to upload the firmware>
I loaded the .ino file into the software and clicked upload. (I think there was a total of 73 files that loaded in the Arudiono for the upload
I loaded the .ino file into the software and clicked upload. (I think there was a total of 73 files that loaded in the Arudiono for the upload