Page 2 of 4
Re: Require full Prusa I3 Aluminium Kit Assembly Instruction
Posted: Wed Feb 11, 2015 2:29 pm
by zhangxueyou
You are welcome. Hope you enjoy your printing later.
Cheung Weng
Re: Require full Prusa I3 Aluminium Kit Assembly Instruction
Posted: Thu Feb 12, 2015 11:50 am
by Anabatix
Hi,
A couple more questions.
1. I think I must cut the white plug off the 12vDC power, strip and screw into board directly? As the photo you show can't be the same board design as in the kit for Ramps 1.4... correct?
2. The 2x Z Axis stepper motors, the white plugs to connect to the Ramps board will never fit. Have you tried it on your Kit. What do you suggest for an easy fix?
3. Could you post some good photos of a completed Prusa Alu Kitset so I can check the layout is as intended. Your manual does not show board or extruder mounting etc. And cable layout around motors.
4. Could you post a Ramps 1.4 finished wiring photo as it is worth 1000 words. And will explain better the power, fan and heatbed wiring using this kitset.
Thanks,
Lee
Re: Require full Prusa I3 Aluminium Kit Assembly Instruction
Posted: Fri Feb 13, 2015 9:42 am
by zhangxueyou
I will give you the pictures of all the wiring of all the parts. Please, you must understand my pictures because I spent a lot time assembling. If you have any problem, please reply me T_T
Ramp1.4+Mega2560
- image1.png (319.87 KiB) Viewed 36450 times
- image2.png (450.45 KiB) Viewed 36450 times
Jumper caps
- image3.png (596.52 KiB) Viewed 36450 times
Re: Require full Prusa I3 Aluminium Kit Assembly Instruction
Posted: Fri Feb 13, 2015 9:45 am
by zhangxueyou
Cooling fan for mainboard
- Cooling fan.png (397.42 KiB) Viewed 36451 times
- Cooling fan2.png (524.28 KiB) Viewed 36451 times
Extruder motor
- Extruder motor wiring.png (601.39 KiB) Viewed 36451 times
Re: Require full Prusa I3 Aluminium Kit Assembly Instruction
Posted: Fri Feb 13, 2015 9:49 am
by zhangxueyou
Themistor on hotbed
- Thermistor on hotbed2.png (183.19 KiB) Viewed 36451 times
- Thermistor on hotbed.png (806.05 KiB) Viewed 36451 times
Re: Require full Prusa I3 Aluminium Kit Assembly Instruction
Posted: Fri Feb 13, 2015 9:52 am
by zhangxueyou
Hotbed
- hotbed.png (373.92 KiB) Viewed 36451 times
- hotbed wiring.png (345.6 KiB) Viewed 36451 times
Wirng of Endstop
- wiring of endstop.png (557.72 KiB) Viewed 36451 times
Re: Require full Prusa I3 Aluminium Kit Assembly Instruction
Posted: Fri Feb 13, 2015 9:56 am
by zhangxueyou
Power supply
Re: Require full Prusa I3 Aluminium Kit Assembly Instruction
Posted: Fri Feb 13, 2015 9:56 am
by zhangxueyou
LCD
- LCD.png (493.32 KiB) Viewed 36451 times
- LCD wiring.png (569.16 KiB) Viewed 36451 times
Re: Require full Prusa I3 Aluminium Kit Assembly Instruction
Posted: Fri Feb 13, 2015 9:58 am
by zhangxueyou
Wiring of extruder
- Wiring of extruder.png (534.37 KiB) Viewed 36451 times
Wiring of thermistor for extruder
- Wiring of themistor for Exturder.png (419.83 KiB) Viewed 36451 times
Re: Require full Prusa I3 Aluminium Kit Assembly Instruction
Posted: Fri Feb 13, 2015 10:00 am
by zhangxueyou
Switch
- switch1.png (345.89 KiB) Viewed 36451 times
- switch2.png (561.54 KiB) Viewed 36451 times