Re: Err: MINTEMP LCD and Repetier-Host
Posted: Wed Mar 25, 2015 3:26 pm
- IMG_1633.JPG (133.84 KiB) Viewed 14884 times
- IMG_1633.JPG (133.84 KiB) Viewed 14884 times
Geeetech
Here you can share you great ideas about hardware innovation. Here you can enjoy more professional and specialized services, Here is a platform for you to make a difference!
https://forum.geeetech.com/
Err: MINTEMP LCD and Repetier-Host
Page 2 of 3
Re: Err: MINTEMP LCD and Repetier-Host
Posted: Wed Mar 25, 2015 4:08 pm
When you unplug the wires, the screen displays like this picture:
When you plug 2 jumper caps to to mainboard, the screen displays like this picture:
Check it.
- QQ截图20150325160105.png (287.94 KiB) Viewed 14885 times
- QQ截图20150325160407.png (546.83 KiB) Viewed 14885 times
- QQ截图20150325160131.png (249.58 KiB) Viewed 14885 times
- QQ截图20150325160219.png (424.35 KiB) Viewed 14885 times
Re: Err: MINTEMP LCD and Repetier-Host
Posted: Thu Mar 26, 2015 1:29 am
Started the printer this morning and there was no MINTEMP error. Heated the extruder and bed to test. Everything worked fine. Let it cool down, shut it off, came back after lunch started it up, and now has MINTEMP error again. I am at a total loss as to what is wrong with this thing. Between the missing parts, bad firmware, and errors this is very frustrating. Especially after paying over $400 for the printer.
Re: Err: MINTEMP LCD and Repetier-Host
Posted: Thu Mar 26, 2015 3:09 am
With both thermistors unplugged the hotbed displays 0/0 but the hot end shows 22/0.
Re: Err: MINTEMP LCD and Repetier-Host
Posted: Thu Mar 26, 2015 3:18 am
Yes when I put jumpers on the pins as in the picture, both read 0/0, 0/0 and MAXTEMP BED
Re: Err: MINTEMP LCD and Repetier-Host
Posted: Thu Mar 26, 2015 9:05 am
Please refer to these pictures and check if somewhere on the back side of boards is short.
- ArduinoMega2560_R3_Back.jpg (89.46 KiB) Viewed 14884 times
- Rampsback.jpg (61.51 KiB) Viewed 14884 times
Re: Err: MINTEMP LCD and Repetier-Host
Posted: Thu Mar 26, 2015 10:24 am
I think I may have found the problem, a short in the connector. Checking now, and I will also check the back of the board.
Re: Err: MINTEMP LCD and Repetier-Host
Posted: Thu Mar 26, 2015 11:26 am
- IMG_1645.JPG (100.93 KiB) Viewed 14883 times
- IMG_1640.JPG (114.06 KiB) Viewed 14883 times
Re: Err: MINTEMP LCD and Repetier-Host
Posted: Thu Mar 26, 2015 11:30 am
Now that the boards are back together both are reading 0/0, 0/0 and still Err: MINTEMP
Re: Err: MINTEMP LCD and Repetier-Host
Posted: Thu Mar 26, 2015 6:05 pm
Hi,retaf99
Have you received my email?
Please send me your pruchase link and your order number.
My email: Cheung.Weng@geeetech.cn
Have you received my email?
Please send me your pruchase link and your order number.
My email: Cheung.Weng@geeetech.cn