Firmware for geeetech 3D printers

[Mark]

--Hi guys, all the firmware for geeetech 3D printers are here,
please choose your printer type download it, tks!

---------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------

Note: if you don't know how to install the firmware, come here:
1. For board GT2560 and sanguinololu:
http://www.geeetech.com/forum/viewtopic ... 13&t=17181
2.For the board GTM32 (prusa I3 M201), please come to here install the firmware:
Using ST-link: http://www.geeetech.com/forum/viewtopic ... 13&t=17173
Using USB port: http://www.geeetech.com/forum/viewtopic ... 20&t=17597
3.If your board is GTM32 pro with 3 in 1 hotend, come here to install the firmware:
http://www.geeetech.com/forum/viewtopic ... 20&t=18167
4. If your board is GTM32 PRO VB, check out this link:
http://www.geeetech.com/forum/viewtopic ... 20&t=60425
5. If one of your axis direction is reversed, check out this link:
http://www.geeetech.com/forum/viewtopic ... 17&t=17037
6. After installing the firmware, if the LCD is beeping all the time and has two rows of blocks, then you must have installed the wrong firmware, please check it agian!

Note:
Check the threaded rod of your printer(Especially I3 PRO X, I3 PRO W, I3 PRO B, I3 PRO C)
If your printer working with T8 threaded rod
You need to send Gcode"M92 Z400" via USB port.(When you upload the firmware finished)
Then you need to send Gcode"M500" to save the setting.

T8.jpg (16.99 KiB) Viewed 1518856 times

1) Firmware for Prusa I3 M201
For the new board(GTM32 Pro VB)on M201:

M201_V1.0.01.rar

(58.24 KiB) Downloaded 10851 times

gtm32_machine_m201.zip

(62.23 KiB) Downloaded 13445 times

The latest version(for GTM32) :

GTM32_V1.0.5.zip

GTM32_V1.0.5

(98.94 KiB) Downloaded 17779 times

Note:
V1.0.5 added some G-code commands on the base of V1.0.4:
M92: Set axis_steps_per_unit
M110: Set Current Line Number M500
M502: Revert to the default "factory settings."
M300: Play beep sound
M304: Set PID parameters - Bed

V1.0.4 has fixed some bugs and the pause problem in the old ones, check out this link for more details:
http://www.geeetech.com/forum/viewtopic ... 20&t=17279

The old version:

GTM32_V1.0.4.zip

GTM32_V1.0.4

(97.15 KiB) Downloaded 11347 times

GTM32_1.0.3.zip

GTM32_V1.0.3

(96.01 KiB) Downloaded 10537 times

GTM32-V1.0.0.zip

(96.05 KiB) Downloaded 9866 times

GTM32-old.zip

(92.53 KiB) Downloaded 9990 times

2) Firmware for Prusa I3 X(GT2560)

I3_pro_X.zip

(295.69 KiB) Downloaded 39746 times

if you have upgrade your pro X into a dual extruder, please use this firmware

Marlin-PI3_Pro_X2.zip

(299.37 KiB) Downloaded 17378 times

3) Firmware for Aluminum I3
For sanguinololu, you need to copy the folder named "sanguino" to the folder "hardware" of Arduino IDE.
The "sanguino" folder:

sanguino.zip

(209.25 KiB) Downloaded 11990 times

Download this file and unzip it and move it to the folder "hardware".

1 for sanguinololy.jpg (34.93 KiB) Viewed 1602197 times

Then you can use the Arduino IDE 1.0.1 to upload the firmware as the link:
http://www.geeetech.com/forum/viewtopic ... 20&t=16433
For the old aluminum i3(with printed extruder bracket and gear), use the firmware below:
aluminum I3 Ramps 1.4

PI3_Ramps14固件.rar

(199.43 KiB) Downloaded 11407 times

aluminum I3 sanguinololu

PI3_Sanguinololu固件.rar

(229.44 KiB) Downloaded 11743 times

For the full aluminum I3, use the firmware here:

for the upgraded kit using lead screw

Plusa_I3_A_sanguinololu(for the upgraded kit using lead screw).zip

(242.47 KiB) Downloaded 11576 times

aluminum I3 Ramps 1.4

Prusa I3A 2560.zip

(281.17 KiB) Downloaded 13617 times

aluminum I3 sanguinololu

Plusa I3 A sanguinololu.zip

(242.28 KiB) Downloaded 13217 times

4) For prusa I3 A Pro with the 3-in-1 3D printer control box:

PI3A Pro.zip

prusa I3 A Pro

(375.46 KiB) Downloaded 12975 times

for the upgraded kit using lead screw:

PI3A Pro(for the upgraded kit using lead screw).zip

(375.46 KiB) Downloaded 13032 times

if you upgrade your prusa I3 A Pro with dual extruder, please download the firmware here.

PI3A_Pro2.zip

prusa I3 A Pro with dual extruder

(375.73 KiB) Downloaded 10139 times

for the upgraded kit using lead screw:

PI3A Pro2(for the upgraded kit using lead screw).zip

(375.73 KiB) Downloaded 9828 times

5) Firmware for I3 pro&proB
I3 pro&proB(GT2560)

Marlin-PI3_Pro_B.zip

(299.2 KiB) Downloaded 65624 times

I3 pro&proB(ramps)

PI3B-ramps.rar

PI3B-ramps

(229.7 KiB) Downloaded 18253 times

I3 pro&proB(sanguinololu)

PI3B-Sanguino.rar

PI3B-sanguinololu

(229.88 KiB) Downloaded 15298 times

Marlin-PI3_Pro_B_3DTouch.zip

(314.85 KiB) Downloaded 14122 times

Marlin-PI3_Pro_B_3DTouch (A+).zip

(324.69 KiB) Downloaded 17303 times

6) Firmware for I3 pro C
Update:
Fixed the endstop error(Default endstop logic status is the"false")
2019/2/27
Marlin 1.1.8 for proC with GT2560VA/A+/2.0
1.Inculde 3dtouch config and no 3dtouch cofing
2.Added the new menu for extruder+hotend

Getech i3 pro C (Marlin 1.1.8 for all).zip

(2.64 MiB) Downloaded 11716 times

-----------------------------------------------------------------------------------------------------
-----------------------------------------------------------------------------------------------------
I3 pro C (GT2560)

Marlin_GT2560-PI3_Pro_C.zip

Marlin_GT2560-PI3_Pro_C.zip

(299.21 KiB) Downloaded 27025 times

I3 pro C (ramps)

PI3B-Ramp14-2E.rar

PI3B-Ramp14-2E.rar

(268.97 KiB) Downloaded 11983 times

I3 pro C (GT2560 A+)

I3proC （ A+ board ）.zip

(311.94 KiB) Downloaded 10639 times

I3proC （3d touch）.zip

(321.01 KiB) Downloaded 9528 times

I3proC （3d touch A+ board）.zip

(322.54 KiB) Downloaded 10201 times

7) Frimware for Delta G2/G2S

For plastic G2/G2S with printed plastic spider and carriages:

RKMA_GT2560_G2.zip

RKMA_GT2560_G2.zip

(283.11 KiB) Downloaded 10254 times

RKMA_GT2560_G2s.zip

(372.37 KiB) Downloaded 10551 times

For metal G2 pro/G2S pro with upgraded metal spider:

RKMB_GT2560_G2.zip

RKMB_GT2560_G2(pro).zip

(372.1 KiB) Downloaded 10887 times

RKMB_GT2560_G2S.zip

RKMB_GT2560_G2S(pro).zip

(372.37 KiB) Downloaded 13294 times

Note:
1. If you run into the problem that the G2S extruder2 drives axial motors when printing, you can try to solve it by reinstall the latest firmware above, and change some setting here: http://www.geeetech.com/forum/viewtopic ... 13&t=17064
2. The probe endstop, if you use the old firmwrare for plastic G2/G2S, X Y Z should connected to pin1 and pin3; and the new firmware for metal G2 pro/G2S pro, it should be pin1 and pin2 , the same with X Y Z endstops, you can refer to the link here:
http://www.geeetech.com/forum/viewtopic ... 619#p27619

8) Frimware for Me ducer

MD1_Sanguino.rar

MD1_Sanguino.rar

(268.83 KiB) Downloaded 9717 times

9) Frimware for Me creator
Me creator(ramps1.4)

ramps14.rar

ramps14.rar

(229.05 KiB) Downloaded 10348 times

Me creator(sanguinololu)

Sanguino.rar

Sanguino.rar

(229.11 KiB) Downloaded 10943 times

10) Firmware for MeCreator2（GT2560 Rev B）

MeCreator2固件.zip

(293.54 KiB) Downloaded 13696 times

Update:new version of mecreator2
(fixed the print area not correct)

MeCreator2-1.0.4.zip

(305.39 KiB) Downloaded 9968 times

11) Firmware for Rostock 301（GTM32 Pro）
The latest version(Max extruder temp 220℃):

Rostock301_V1.0.03.zip

(63.71 KiB) Downloaded 10259 times

The firmware(Max extruder temp 270℃)

gtm32_machine_delta.zip

(64.11 KiB) Downloaded 9748 times

The old version:

Rostock301_V1.0.02.zip

(63.58 KiB) Downloaded 12021 times

gtm32_machine_delta_V1.0.01.zip

(63.6 KiB) Downloaded 10935 times

12) Firmware for Duplicator 5

Duplicator5.zip

(285.92 KiB) Downloaded 9104 times

13) Firmware for Pro W

ProW.zip

(299.49 KiB) Downloaded 20264 times

update:Firmware for PROW+3Dtouch

I3 ProW GT2560A+ with 3dtouch.zip

(292.26 KiB) Downloaded 11840 times

14) Firmware for A10/A10M/A20/A20M
Note:
Fixed the bug of homing speed too fast when the printer work with 3dtouch
2018.12.27
Increase the value of Estep from the default 340 to 430(For A10M and A20M)
2018.1.9


Note:
I. Please use Arduino 1.8.5 to finish the upload
II. The firmware includes these:
-configuration.h for 3dtouch
-configuration.h for no 3dtouch
You can find it on"Configuration and hex file",choose the correct configuration.h and replace the old one.
III.Enabled "babystep Z"
Click LCD>Click"Info screen",then you can adjust it.
IV.Improved the LCD use experience
V.Improved the mixer color function, easier to use(A10M/A20M)


1.Geeetech A10 with GT2560VB board

A10_marlin_VB 1.1.8.zip

(2.69 MiB) Downloaded 10186 times

2.Geeetech A10 with GT2560V3 board

A10_marlin1.1.8.zip

(2.65 MiB) Downloaded 13001 times

3.Geeetech A10M

A10M_marlin1.1.8.zip

(2.69 MiB) Downloaded 12351 times

4.Geeetech A20 with LCD12864

A20_Marlin-1.1.x12864.zip

(1.18 MiB) Downloaded 9921 times

5.Geeetech A20M with LCD12864

A20M_Marlin-1.1.x12864.zip

(2.33 MiB) Downloaded 15165 times

You can find more info on Github:
https://github.com/Geeetech3D/Prusa_I3_3Dprinter


15) For E180/D200/A30
Please refer to this post and upload the correct firmware
http://www.geeetech.com/forum/viewtopic ... 222#p82222

[mava70]

hello in PI3B-ramps.rar there is not Marlin.ino how to compile?

thanks

[Mark]

You can use Ctrl+A to select all the files and drag all of them to the arduino as the link here shows:
http://www.geeetech.com/forum/viewtopic ... 20&t=16433

[rmrodrigues]

Hi,
How I know that a new version of firmware is available?
Cheers,
RMRodrigues

[Mark]

We'll keep all of them updated, and if a new version is available we'll let you know too, tks!

[mava70]

Hello,

is it possibile to update Marlin firmware downloading it from github and allineate config.h from your config and new Marlin firmware? Did you do some kind of code personalization in you firmware outside of config.h?

I am interested in RAMPS version.

Thanks

Marco

[Mark]

you can do it as you said but note that the marlin version shoud be the same.

[azzraell]

Hi, iam very new at 3d printing, do i have to download the Ramps file and the Marlin file? or which one do i need? I have the Prusa I3 pro B, and the board is the GT2560, but iam kind of lost, not sure what to do. thanks for the help!

[Mark]

your printer is I3 pro B with GT2560, then just download this one:

QQ截图20151201112650.jpg (89.21 KiB) Viewed 1749665 times

[azzraell]

Thanks alot, i have a new problem now, the printer wont home on Y axis, it does ok in the x and z axis, but wont work on the Y, any ideas why wont work? what can i do? thanks!