New mother card works but problem Z axis

[regisregis]

Thanks, yes. it works now :)

But again a problem, my first print is an horror!
The filament doesn't move verry well, heating not very well with your green filament. not liquid!

head : 220° , filament compact...

[Gingko]

[quote=regisregis post_id=84344 time=1527538273 user_id=65381]
Thanks, yes. it works now :)

But again a problem, my first print is an horror!
The filament doesn't move verry well, heating not very well with your green filament. not liquid!

head : 220° , filament compact...
[/quote]

Could you show up more details with video or photos?

or you can check these posts first:
viewtopic.php?f=19&t=17097
viewtopic.php?f=19&t=18507

[regisregis]

Yes i Have :
https://drive.google.com/open?id=11AD7k ... land5tj2TA

a red light on my card when it heats

[Gingko]

[quote=regisregis post_id=84352 time=1527598547 user_id=65381]
Yes i Have :
https://drive.google.com/open?id=11AD7k ... land5tj2TA

a red light on my card when it heats
[/quote]

It seems that the filament can put out smoothly, then it just cools down in the air.
The nozzle is too high and far away from hotbed so that filament cannot stick on it.
You can level the bed first according to user manual.

[regisregis]

But it does not go out whatever the level of the head

[regisregis]

Hi,
again me :)

I can print a cube, but what's type of filament send with the print? because i'm heating more 225°and the quality is bad.

Look
https://drive.google.com/file/d/1jKL1KK ... sp=sharing
https://drive.google.com/file/d/1l17X9c ... sp=sharing

Regards

[Gingko]

[quote=regisregis post_id=84429 time=1528041696 user_id=65381]
Hi,
again me :)

I can print a cube, but what's type of filament send with the print? because i'm heating more 225°and the quality is bad.

Look
https://drive.google.com/file/d/1jKL1KK ... sp=sharing
https://drive.google.com/file/d/1l17X9c ... sp=sharing

Regards
[/quote]

HI! I saw your video.
The filament sent with the printer is PLA,
hotend temp: 190-210C
hotbed temp: 60-75C

I think you can increase the infill density.

I also notice that there is some layer shift with the cube.
You can check if is the voltage of A4988(X-axis) a little low.
And check the belt, maybe it's not tight enough.

[regisregis]

Thanks
you can specify :

>You can check if is the voltage of A4988(X-axis) a little low.
>And check the belt, maybe it's not tight enough.

[regisregis]

Hi,
I think a problem with buse or extruder, i buy a ABS 1.75
but the extruder accepts 1.75? or only 3? Because in the configuration, you can change the configuration E3 diameter min 2mn.
I can use 1.75 filament?

Thanks

[Gingko]

Hi,
I think a problem with buse or extruder, i buy a ABS 1.75
but the extruder accepts 1.75? or only 3? Because in the configuration, you can change the configuration E3 diameter min 2mn.
I can use 1.75 filament?

Thanks

Yes, you can use 1.75mm ABS.
It's not possible to change the setting to 1.75mm?
Change another slice software like repetier host to have a try.