Thanks !
Search found 14 matches
- Mon Nov 18, 2019 7:53 pm
- Forum: Geeetech A20M
- Topic: Marlin 1.1.9 firmware upgrade
- Replies: 8
- Views: 13652
Re: Marlin 1.1.9 firmware upgrade
- Fri Nov 15, 2019 11:05 pm
- Forum: Geeetech A20M
- Topic: Marlin 1.1.9 firmware upgrade
- Replies: 8
- Views: 13652
Re: Marlin 1.1.9 firmware upgrade
Hi DzzD, can you share your configuration.h ?DzzD wrote: Mon Nov 04, 2019 7:46 pm Yes, I've tested it, compiled and running on my A20m, but didn't see any quality improvement.
Thx
Ju
- Wed Nov 13, 2019 11:11 pm
- Forum: Geeetech A20M
- Topic: unable to print anything after firmware update.
- Replies: 7
- Views: 9935
Re: unable to print anything after firmware update.
It is really strange, before update I can print at 190°C without any problem.
Now at 240 °C I have problems to print (same PLA)
Did someone know where to buy only 2 throat with the cooper screen ? (like photo here :https://github.com/caesar1111/Geeetech-A10M-HotEnd-Maintenance/blob/master/A10M ...
Now at 240 °C I have problems to print (same PLA)
Did someone know where to buy only 2 throat with the cooper screen ? (like photo here :https://github.com/caesar1111/Geeetech-A10M-HotEnd-Maintenance/blob/master/A10M ...
- Wed Nov 13, 2019 4:00 pm
- Forum: Geeetech A20M
- Topic: unable to print anything after firmware update.
- Replies: 7
- Views: 9935
Re: unable to print anything after firmware update.
Hi, I find this:https://github.com/caesar1111/Geeetech-A10M-HotEnd-Maintenance/blob/master/A10M_HotEnd_Maintenance.md?fbclid=IwAR2m9YfvyLMxZt9GrO9P-Yo_tkeimUOhN-WSzkA9lke5jd-LJUGLLw0IqLw
Thank you William,
That is what I've made expect some parts (I did not seal the throat with silicon)
And ...
- Wed Nov 13, 2019 2:10 am
- Forum: Geeetech A20M
- Topic: unable to print anything after firmware update.
- Replies: 7
- Views: 9935
Re: unable to print anything after firmware update.
I've just test my thermistor, read 157 khoms, with is exactly the same as my other thermistors (it's 15°C in the garage)
My Marlin config lokk good :
So the last thing I see is a hotend problem like many others ?
Ju
My Marlin config lokk good :
Code: Select all
#define TEMP_SENSOR_0 1
Ju
- Tue Nov 12, 2019 6:40 pm
- Forum: Geeetech A20M
- Topic: unable to print anything after firmware update.
- Replies: 7
- Views: 9935
Re: unable to print anything after firmware update.
:D Hi, If you are referring to firmware with 3d touch,
You can refer to this for an update: http://www.geeetech.com/forum/viewtopic.php?f=20&t=17046
You can provide a specific picture of your problem so that we can solve the problem better.
Thank for your response.
At this moment, I don't ...
- Tue Nov 12, 2019 3:34 am
- Forum: Geeetech A20M
- Topic: unable to print anything after firmware update.
- Replies: 7
- Views: 9935
unable to print anything after firmware update.
Hi,
I've tried to install a BL touch, and I flash my new A20M (v2?) with the official firmware found on geeetech github.
I was unable to have a correct bed level, I've remove the bl touch and I flash the same firmware without BLtouch support.
The result is catarstrophic, unable to print ...
I've tried to install a BL touch, and I flash my new A20M (v2?) with the official firmware found on geeetech github.
I was unable to have a correct bed level, I've remove the bl touch and I flash the same firmware without BLtouch support.
The result is catarstrophic, unable to print ...
- Thu Nov 07, 2019 3:15 pm
- Forum: Geeetech A20M
- Topic: New A20M Model ?
- Replies: 18
- Views: 72559
Re: New A20M Model ?
Here the photo much easier to understand.
Does anybody know what is the 3 poles connector under ?
Ju
- Thu Nov 07, 2019 3:37 am
- Forum: Geeetech A20M
- Topic: New A20M Model ?
- Replies: 18
- Views: 72559
Re: New A20M Model ?
You have the 5 pins at the top of the small board, just under the big connector
Ju
- Tue Nov 05, 2019 6:30 am
- Forum: Geeetech A20M
- Topic: New A20M Model ?
- Replies: 18
- Views: 72559
Re: New A20M Model ?
yes stepper drivers.
I've seen nothing on them. It is for selecting in your Marlin 2 config.
Thanks
Ju
I've seen nothing on them. It is for selecting in your Marlin 2 config.
Thanks
Ju